01-15-2008
"I did some research and found out that LPAR is possible on JS20 with VIOS +IVM..."
Where did you find this information?
I do not believe the JS20 supports LPAR or IVM, only the JS21 supports this.
10 More Discussions You Might Find Interesting
1. AIX
Hello to all,
Goal: Efficiently allow for mass deployment of AIX to PSeries hardware.
Problems: Numerous, too many to list here.
Now for a rather lengthy expansion...
Let me just go ahead and say that I am desperately and humbly asking for as much experienced assistance as I can get. If... (0 Replies)
Discussion started by: get2work
0 Replies
2. AIX
I have a P570 that for some reason is not allowing the P1-T6 NIC to be recognized. I have confirmed from the HMC that it is set for the LPAR, but when I do a cfgmgr, it won't recognize it. It though is recognizing the slot cards just fine which are P1-C3 for one shelf and P1-C3 of another shelf.... (1 Reply)
Discussion started by: LegendMan
1 Replies
3. AIX
I know that IBM's official stance is that NIM does not work on etherchannel environment, but has anyone able to get around it?
I'm working on a p5-590 LPAR system, and the NIM master and clients are all on the same frame.
Any help is appreciated. (1 Reply)
Discussion started by: pdtak
1 Replies
4. AIX
Hi,
I have 2 lpars on my AIX that needs to be started manually after each reboot.
Because the servers are storing the NFS and NIS info, other servers won't run correctly until they start up.
I found in IBM documentation the steps to make it automatic.
My question is, I want to know if... (2 Replies)
Discussion started by: rahzzbietel
2 Replies
5. AIX
Hello,
I am new to AIX...
I am having this problem trying to re-install AIX 5L 5.2 on a blade (JS20)
Then update it to 5.3
This blade now has 5.3 and needs to be re-install
But the problem is when I press 1 while it is restarting....
I see the message: SMS menus are not supported on... (4 Replies)
Discussion started by: mifch
4 Replies
6. AIX
I am planning for System P with 2 number of 2-core processor (4 core in total).
Can I make 3 LPARS with this processor configuration without the support of micropartitioning, that means with simple LPAR only. (3 Replies)
Discussion started by: pchangba
3 Replies
7. AIX
Hi all,
I have the following configuration
2 ds3524 storage disk systems located over 2 locations
2 P720 server located over 2 locations
DS3524 are connected to san switch.
Each vio server has 1 fc adapter attached to a san switch.
per p720 server 2 virtual io servers. Vio 1 has 1 lun... (2 Replies)
Discussion started by: markiemark
2 Replies
8. AIX
Unix Guys
i want to setup a lab in my house for learning, i want to setup and hacmp and a seperate server where i can setup 2 lpars and then cluster those 2 lpars and setup them up for failover
what is the cheapest way to achive this.
my objective is to learn hmc -> managed server via... (7 Replies)
Discussion started by: asyed123
7 Replies
9. AIX
Hi Gurus,
Can a AIX server with 4 LPARs, each having it's own hostname on the same physical host. Is this possible?
Thanks,
S (2 Replies)
Discussion started by: svajhala
2 Replies
10. AIX
There can be configurations in IBM Server wherein a
standalone partition is created on some supported IBM Server
Or
A VIOS - VIOC LPARs created.
Now in both cases they are lpars. But if I want to differentiate b/w a standalone LPAR vs an VIOC LPAR how can I do..?
On a... (2 Replies)
Discussion started by: Manish00712
2 Replies
GXL2GV,GV2GXL(1) General Commands Manual GXL2GV,GV2GXL(1)
NAME
gxl2gv,gv2gxl - GXL-GV converters
SYNOPSIS
gxl2gv [ -gd? ] [ -ooutfile ] [ files ]
gv2gxl [ -gd? ] [ -ooutfile ] [ files ]
DESCRIPTION
gxl2gv converts between graphs represented in GXL and in the GV language. Unless a conversion type is specified using a flag, gxl2gv will
deduce the type of conversion from the suffix of the input file, a ".gv" (or a ".dot") suffix causing a conversion from GV to GXL, and a
".gxl" suffix causing a conversion from GXL to GV. If no suffix is available, e.g. when the input is from a pipe, and no flags are used
then gxl2gv assumes the type of the input file from its executable name so that gxl2gv converts from GXL to GV, and gv2gxl converts from GV
to GXL.
GXL supports a much richer graph model than GV. gxl2gv will attempt to map GXL constructs into the analogous GV construct when this is pos-
sible. If not, the GXL information is stored as an attribute. The intention is that applying gxl2gv|gv2gxl is semantically equivalent to
the identity operator.
OPTIONS
The following options are supported:
-g The command name and input file extensions are ignored, the input is taken as a GV file and a GXL file is generated.
-d The command name and input file extensions are ignored, the input is taken as a GXL file and a GV file is generated.
-? Prints usage information and exits.
-o outfile
If specified, the output will be written into the file outfile. Otherwise, output is written to standard out.
OPERANDS
The following operand is supported:
files Names of files containing 1 or more graphs in GXL or GV. If no files operand is specified, the standard input will be used.
RETURN CODES
Both gxl2gv and gv2gxl return 0 if there were no problems during conversion; and non-zero if any error occurred.
BUGS
gxl2gv will only convert in one direction even if given multiple files with varying suffixes.
The conversion can only handle one graph per GXL file.
There are some GXL constructs which gxl2gv cannot handle.
AUTHORS
Krishnam Pericherla <kp@research.att.com>
Emden R. Gansner <erg@research.att.com>
SEE ALSO
dot(1), libgraph(3), libagraph(3), neato(1), twopi(1)
20 December 2002 GXL2GV,GV2GXL(1)