01-14-2008
Fibre Cards
What kind of systems are you putting these cards in? What type of storage device are you using? There may be some specific software necessary for your disks.
Normally there is no issue with the install. Where things can get exciting is in the zoning and allocation of resources on the SAN device.
Good luck.
Shawn
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi there, I'm a newbie so please be patient. I wanted to know if it was possible to run X server on a box w/o a video card. The reason I want to do this is I'd like to have a CDE session from sun workstation into the AIX box. Please let me know if this is feasible. Thanks for your time. (5 Replies)
Discussion started by: blah00000
5 Replies
2. Solaris
Hi,
After I installed Solaris 10 in the Intel platform (chipset 865*) network card was not detected, were shall I get this driver? iam new to Solaris. (2 Replies)
Discussion started by: pravin_2929
2 Replies
3. Debian
I've had no luck with help on linuxquestions so I figured I'd try here. I'm using debian etch.
The problem is that I can not install my network card because it says:
Makefile:62: *** Linux kernel source not found. Stop.
I have the kernel-headers installed.
I've looked all over the... (9 Replies)
Discussion started by: Virtuality
9 Replies
4. AIX
Want to configure IBM raid strorage but the aix 5L cds do not have the drivers for the fibre channels. The machine is RS/6000. I have gone to IBM downlaodable sites but i can't find the drivers? help pliz:mad: (4 Replies)
Discussion started by: Zim-Aix-Guru
4 Replies
5. Solaris
Hi all
i would like to ask some suggests about my next job!
I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid.
The problem come in if every disk is now controlled by the HBA, how can I install the OS?
No disk is being detected by the OS.
SAS card... (2 Replies)
Discussion started by: kakabobo
2 Replies
6. UNIX for Dummies Questions & Answers
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies
7. War Stories
Hi Folks,
A couple of years ago we had to replace the core switches between two of our data centres, a simple task for the most part - these new switches would be state of the art Cisco Catalyst units.
The link between the two sites was a dark fibre, with 8Gb bandwidth running full duplex... (9 Replies)
Discussion started by: gull04
9 Replies
8. AIX
Hello,
Just a quick question
Usually from a PSERIES if you want to connect to IBM SAN Storage
you connect the IBM SAN Storage through a SAN Switch
something like this
---
however my question
Can you connect
from Pseries directly to San Storage without SAN Switch
what would be... (8 Replies)
Discussion started by: filosophizer
8 Replies
9. AIX
Hello all,
Let me introduce about the context and my environment.
We have an AIX 6.1 system, it has 4 FC channels
/ > lsdev -Cc adapter | grep fcs
fcs0 Available 23-T1 Virtual Fibre Channel Client Adapter
fcs1 Available 23-T1 Virtual Fibre Channel Client Adapter
fcs2 Available 23-T1... (14 Replies)
Discussion started by: Phat
14 Replies
SMODE2(1) FSF SMODE2(1)
NAME
mode2, smode2, xmode2 - shows the pulse/space length of infrared signals
SYNOPSIS
smode2 [options]
DESCRIPTION
The main purpose of these programs is to check operation of your home-brew LIRC receiver hardware and to see the IR waveform of the remote
controller without an expensive oscilloscope. Very useful for debugging. Of course this program won't work with hardware that decodes the
signals itself like e.g. TV cards or the Irman.
smode2 uses the svgalib to show the IR waveform in a graphical representation. The time division is variable from 1 ms/unit to extremely
high values (integer type) but there is no point increasing this value above 20 ms/unit, because one pulse is about 1 ms. This kind of pre-
sentation is much more exciting than the simple pulse&space output showed by mode2.
-h --help
display usage summary
-v --version
display version
-d --device=device
read from given device
-t --timediv=value
ms per unit
SEE ALSO
mode2(1), smode2(1), xmode2(1)
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
smode2 0.8.7pre1 May 2010 SMODE2(1)