Sponsored Content
Full Discussion: sun 420r hme0 not responding
Operating Systems Solaris sun 420r hme0 not responding Post 302155651 by frank_rizzo on Saturday 5th of January 2008 12:51:36 AM
Old 01-05-2008
when did this last work?

what does ifconfig -au show?

what does ifconfig -a show?

what does dmesg|grep hme show?

Has the physical cabling and switch/port been verified?
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

hme0 babble -- ?

Dear Reader, I have a very unique problem. Quite often my on board ethernet port( hme0 ) related message is appearing in /var/adm/messages. The message is hme0: babble.. The port is up and alive. What does this message mean.. Is the on board port is about to fail?? Thanks in advance, (2 Replies)
Discussion started by: joseph_shibu
2 Replies

2. UNIX for Advanced & Expert Users

Hme0 interfaces...

How do you configure more than one network on a single hme0 interface under SunOS? And why would you want to do this? Thanx :) -Michelle (1 Reply)
Discussion started by: Michelle1977
1 Replies

3. Solaris

hme0 problem after reboot

Hi ..... My problem is that when i reboot the system i can't connect to the network because my ethernet ( hme0 ) is down , i must up it by ifconfig command after reboot : # ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask... (1 Reply)
Discussion started by: tt155
1 Replies

4. Solaris

Install solaris 2.6 on Enterprise 420R

I am needing to install solaris 2.6 on a Enterprise 420R with 4X450mHz. Documentation says you need Operating Enviroment Installation CD February 2000(704-7076-10). Does anyone know where I can get this? (4 Replies)
Discussion started by: jenyart
4 Replies

5. Solaris

Sun V890: RSC firmware not responding

Hi all, After the V890 server shutdown unexpectedly, it became unaccessible from RSC. There is one error message about it: rscadm: RSC firmware not responding Do you have experienced this? Please help! (1 Reply)
Discussion started by: bamboonix
1 Replies

6. Solaris

How to show memory modules on 420R

I'm trying to determine what memory modules the box has so they can be ordered from a 3rd-party source and be replaced in-house (the box is not under warranty) I have a 420R running Solaris 9. # uname -a SunOS agatlsun04 5.9 Generic_118558-36 sun4u sparc SUNW,Ultra-80 Recently got a... (4 Replies)
Discussion started by: agcodba
4 Replies

7. UNIX for Dummies Questions & Answers

Console connection enterprise 420r

Hellow, i bought a sun enterprise 420r. I would like to connect to the console for installation of a new operating system (solaris 10) I made a connection from a usb --> com-port --> serial port of the server. I configured my hyperterminal (9600 8n1) and when i connect to my server and... (2 Replies)
Discussion started by: chelle007
2 Replies

8. Solaris

Sun Enterprise 420R

I am trying to connect to our Sun Enterprise 420R server via Hyperterminal. Using settings of 9600,n,1,n, I am getting nothing on COM4 (my laptop's ethernet port). I've also tried COM3, COM2, and COM5 - but at least I can type in COM4: the other three I cannot type when trying to connect. I am... (2 Replies)
Discussion started by: jmcgranahan
2 Replies

9. Solaris

ifconfig hme0 plumb not working

Hiii folks,, I am unable to configure NIC using hme0 command. I am getting an error message as "hme0: File or directory not found.." can someone help me... Bhagi... (9 Replies)
Discussion started by: bhargav90
9 Replies

10. Solaris

Sun enterprise 420R boot issue

Hi, I am using sun enterprise 420R server. Problem is on the monitor i am not able to see anything. I tried Serial connection, on terminal(using serial) i could see that POST(power on start tests) tests are being done, after that "timeout waiting for arp rarp packet" message keep displaying... (11 Replies)
Discussion started by: kkittu009
11 Replies
RGEPHY(4)						   BSD Kernel Interfaces Manual 						 RGEPHY(4)

NAME
rgephy -- RealTek RTL8168/8169/8110/8211 series 10/100/1000 Gigabit Ethernet PHY driver SYNOPSIS
To compile all available PHY drivers into the kernel, place the following line in your kernel configuration file: device miibus Alternatively, to selectively compile this driver into the kernel, place the following lines in your kernel configuration file instead: device mii device rgephy DESCRIPTION
The rgephy driver supports the RealTek RTL8168, RTL8169, RTL8110 and RTL8211 series integrated 10/100/1000 Gigabit Ethernet PHYs. In order to get a list of media types and options supported by a specific instance of the rgephy driver, run ifconfig -m on the instance of its parent MAC driver. Additionally, the rgephy driver supports the following special media option: flag0 When manually setting media type and options via ifconfig(8), the rgephy driver by default also triggers an autonegotiation advertis- ing the selected media. This is done in order to work around hardware issues in certain scenarios. It is believed that this behavior does not cause harm in general but in fact can have an adverse effect in edge cases. In order to manually set the media type and options without also triggering an autonegotiation, the rgephy driver allows to turn this behavior off via the flag0 media option. Note that this special media option will not show up in the output of ifconfig(8), even when set. EXAMPLES
Manually set 100BASE-TX full-duplex without also triggering an autonegotiation: ifconfig re0 media 100baseTX mediaopt full-duplex,flag0 SEE ALSO
intro(4), miibus(4), ifconfig(8) BSD
January 16, 2011 BSD
All times are GMT -4. The time now is 01:36 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy