Hi there,
I just installed a Sparc 4-port Ethernet adapter on my sparc 10 and was wondering how on earth I find out what the names of the ports are. It looks like on startup that on SBus1 there is something called qec qe qe qe qe. So I tried to do an IFCONFIG qe0...but had no success. Can anyone... (3 Replies)
Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
I am trying to find PCI Ethernet cards that are compatible with the IBM RISC 6000 - B50 Power PC. None of the regular NIC's seem to have AIX drivers. Does anyone know of AIX drivers for standard PCI Ethernet NIC's or a non IBM NIC that works with the Model B50 at 10/100 MB ? (0 Replies)
Hi;
I have a UNIX box (SCO 5.0.2) with two (2) NIC cards. One card (NIC1) talks to a network 57.14.65.x/27. The other card NIC2) talks to users on 57.14.103.x and 57.14.105.x with subnet mask of 255.255.0.0. If I set NIC2 to this subnet mask (255.255.0.0) it seems like the NIC traffic is now... (2 Replies)
Hiii... Every one....
I want to know the command to get the details and number of HBA cards
attached to a server.
I know that we can use "powermt display", but nither my cards are connected to the storage nor powerpath is active.
I am using SUN server with Solaris -9.
Thanks in... (4 Replies)
How can I identify how many ethernet adapter cards I have on the server from the below ouput ?
$>lsdev -Cc adapter | grep ent
ent0 Available 06-08 10/100/1000 Base-TX PCI-X Adapter (14106902)
ent1 Available 07-08 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
ent2 ... (5 Replies)
Hi All,
I have just setup a webserver running on a linux box. This server has 2 ethernet cards and only 1 is in used now. eg. 192.168.10.1 is my server IP. All users from 192.168.10.X can access my webserver. However, users from another LAN 10.10.10.X are not able to access my webserver. They... (0 Replies)
hi all,
I am trying to view the hba cards on a rhel7 server (storage says they are there, but I am not seeing them.
I tried lspci -nn | grep -i hba
lspci |grep qla
I tried looking in /sys/class/fc_host.. but it is empty.
I am not sure if I am looking in the right spot... (0 Replies)
Discussion started by: gartie
0 Replies
LEARN ABOUT REDHAT
axnet_cs
AXNET_CS(4) Kernel Interfaces Manual AXNET_CS(4)NAME
axnet_cs - Asix AX88190 chipset PCMCIA Ethernet Driver
SYNOPSIS
insmod axnet_cs.o [pc_debug=n] [irq_list=i,j,...]
DESCRIPTION
Axnet_cs is a driver for PCMCIA ethernet cards based on the Asix AX88190 chipset. These cards are mostly NE2000 compatible but have sev-
eral bugs that are sufficiently tricky to work around that a separate driver was deemed necessary. When this driver is bound to a card, it
allocates the next available ethernet device (eth0..eth#). This device name will be reported in the kernel log file, and passed on to
cardmgr(8).
PARAMETERS
pc_debug=n
Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero
value enables debugging.
irq_list=i,j,...
Specifies the set of interrupts that may be allocated by this driver.
DIAGNOSTICS
axnet_cs: this is not an AX88190 card!
Indicates that this card is probably a normal NE2000 compatible card, which requires the pcnet_cs driver.
eth#: interrupt(s) dropped!
Indicates that the driver did not receive an interrupt notification for some reason. The driver will poll the card (with a signifi-
cant performance penalty) if the problem persists. The most likely cause is an interrupt conflict and/or host bridge configuration
problem.
AUTHOR
David Hinds - dahinds@users.sourceforge.net
SEE ALSO cardmgr(8), pcmcia(5).
pcmcia-cs 2001/08/17 12:51:58 AXNET_CS(4)