01-03-2008
I've worked on several AIX upgrade rollouts in the past 18 months and they always include a reboot at the end as part of our standard procedure. I'm not sure if it is 100% required, you'd have to study the IBM documentation or ask them to be sure. But it is just too risky not to reboot. If you don't do it immediately and there is a problem next time you reboot it will be far harder to troubleshoot. And it may be too late to roll back the upgrade depending on what else has changed since.
9 More Discussions You Might Find Interesting
1. AIX
I've recently installed ServicePack1 for Tecnology_Level 9 of AIX 5.2 .
The result of installation is "OK" but with oslevel -s i dont see the service pack installed ....
after many research i try (with many luck!!)
instfix -i|grep SP
and the result :
All filesets for 5200-08-01_SP... (1 Reply)
Discussion started by: BabylonRocker
1 Replies
2. UNIX for Dummies Questions & Answers
Hello,
I just re-installed the MP3 for UNIXWARE on our system for the second time due to upper management decision and I received this message pasted below.
The following packages were installed successfully:
UnixWare 7.1.4 Maintenance Pack 3 <uw714mp3>
Updated Base System Guides... (0 Replies)
Discussion started by: Yorgy
0 Replies
3. AIX
Hi All,
I was installing apar CVE-2008-0122 on my freshly test aix53.
I followed the ibm site and run this 'installp -a -d libc_ifix -X all'
and got this
+-----------------------------------------------------------------------------+
Pre-installation... (1 Reply)
Discussion started by: itik
1 Replies
4. AIX
Hi,
redbook documentation is telling that IY17981 fix is required for aix 4.3.3 to aix 5L migration. But there is no mention about that fix in any ML installation packages.
- My system is ML11 :
oslevel –r
4330-11
- But xlC.rte is on wrong version :
lslpp -L xlC.rte
xlC.rte ... (3 Replies)
Discussion started by: astjen
3 Replies
5. AIX
Hello, I am trying to install Oracle 11g on my AIX server and it requires at a minimum OS level 5300-05-06. I am currently at 5300-05-01. What do I need to upgrade this? Where can I get this sp? What are the step to install this? I am a DBA not sysadmin. We no longer have a sysadmin. Lucky... (4 Replies)
Discussion started by: dkranes
4 Replies
6. AIX
Hi...
Can i remove one APAR number from aix5.3..
If it is possible how to do..
Thanks.. (3 Replies)
Discussion started by: sumathi.k
3 Replies
7. AIX
Hi All,
I have this fix for AIX (5300-06-06-0811) and i need to install it.
How can i do this?
What are the prerequisites for this fix?
Thanks (1 Reply)
Discussion started by: lucaxvu
1 Replies
8. AIX
We have tried to install an APAR fix IZ20298 on a AIX test server. It is requiring a base level of bos.adt.prof of 5.3.0.0 I cannot find this file anywhere. I fould 5.3.0.1 and it still will not install without the base install. Any ideas where I can find bos.adt.prof 5.3.0.0? (1 Reply)
Discussion started by: daveisme
1 Replies
9. AIX
Hi All,
i'm try to update my aix 6100.06.05 to 6100.07.00.
i download the 4,5 GB of FixPack buy i don't have a required package (devices.chrp.pci.rte 6.1.7.0)
This package does not exist on the fix pack (i've check in the .toc file and in the .bff files)
On ibm website i see that this... (0 Replies)
Discussion started by: Zio Bill
0 Replies
LEARN ABOUT ULTRIX
reboot
reboot(8) System Manager's Manual reboot(8)
Name
reboot - automatic reboot procedures
Syntax
/etc/reboot [ -n ] [ -q ]
Description
The ULTRIX system is booted by loading a kernel image, usually into memory at location zero and transferring to zero. Because the system
is not reenterable, the kernel image must be read in from disk each time the system is bootstrapped.
When the reboot of a running system is desired, is normally used. If there are no users, can be used. The command causes the disks to be
synced, and then a multiuser reboot is initiated. The system is booted and an automatic disk check is performed. If the procedure suc-
ceeds, the system is then brought up for the users.
The system will reboot itself after a power failure or after a crash, provided auto-restart is enabled on your system. A consistency check
of the file systems will be performed and, unless the check fails, the system will resume multiuser operations.
Options
-n Prevents the disks from being synced.
-q Reboots quickly and ungracefully, without shutting down running processes first.
Files
System code
See Also
crash(8v), fsck(8), halt(8), init(8), newfs(8), rc(8), shutdown(8)
reboot(8)