Assigning a static IP to NICs Post: 302155035

10 More Discussions You Might Find Interesting

1. AIX

Merge NICs

Hi friends, I installed oracle 10g (10.2.0.2) RAC on 2 IBM p5 570 servers running AIX 5.3ML04 and HACMP5.2 (used Raw devices, not used GPFS). Each server has 4 x 1Gbps ethernet cards (NICs), en0 and en1 for boot address, en2 and en3 for oracle interconnect. Now i want to merge 2 NICs (en2 and...

2. IP Networking

FreeBSD and two NICs

FreeBSD 4.8, Apache 1.3.27 - two NICs, one with a real-world IP plugged into a switch outside the PIX firewall, the other with a private IP plugged into a switch inside the PIX firewall. Apache listens on both IPs. my domain is mydomain.org. so in /etc/rc.conf i have something like this (these...

3. Solaris

How many NICS do I have?

Hi, is there a way in Solaris 8 to determine how many total NIC's say a Sun Sparc box has installed - plumbed or unplumbed - and find out its capable network speeds and MAC address? I know ifconfig -a but that only shows the plumbed and used interfaces. thx cc

4. Linux

Two NICs one IP address

I'm looking for a way in RHL 5.1 to use two NICs on one host with two physical IP addresses and map them under one virtual IP address, i.e. NIC 1 10.10.10.1 NIC2 10.10.10.2 VIP 192.168.10.1 Basically I want either one of the NICs to ARP for the VIP. No load balancing required just HA.

5. IP Networking

I need HELP to Set up Coyote Linux router with 1 static IP & 64 internal static IP

hello, i need help on setting my coyote linux, i've working on this for last 5 days, can't get it to work. I've been posting this message to coyote forum, and other linux forum, but haven't get any answer yet. Hope someone here can help me...... please see my attached picture first. ...

6. Programming

C++ program is crashing on re-assigning const static member variable using an int pointer

Hi, Can any one tell me why my following program is crashing? #include <iostream> using namespace std; class CA { public: const static int i; }; const int CA::i = 10; int main() { int* pi = const_cast<int*>(&CA::i); *pi = 9; cout << CA::i << endl; }

7. Programming

Even the Static cURL Library Isn't Static

I'm writing a program which uses curl to be run on Linux PCs which will be used by a number of different users. I cannot make the users all install curl on their individual machines, so I have tried to link curl in statically, rather than using libcurl.so. I downloaded the source and created a...

8. Hardware

How to get into BIOS and disable NICS?

Hi, I have to get into BIOS and disable onbaord NICS for an IBM server, can someone please help me out. I tried hitting F1 when reboot to get into BIOS, but it seems like a setup screen and I dont see any option to disable NICS? Thanks Sam

9. IP Networking

Networking 2 NICs

Hi all, Host - Ubuntu 12.04 desktop 64bit Virtualizer - Oracle VirtualBox 2 NICs Where can I find relevant document to set up 2 NICs, one for inward bound and another for outward bound, separate channel, both connected to the same router Would following document be appropriate for my...

10. UNIX for Dummies Questions & Answers

Linux with two NICs

Hello All, I have Linux box with two interface cards. Every card has it's own IP Address and Gateway, IP addresses are from different subnets. eth0 192.168.1.10/24 GW 192.168.1.1 eth1 192.168.2.10/24 GW 192.168.2.1 Third PC is located in 192.168.13.0/24 network and is trying to access...

LEARN ABOUT OPENDARWIN

liebert

LIEBERT(8)							    NUT Manual								LIEBERT(8)

NAME

       liebert - Driver for Liebert contact-closure UPS equipment

NOTE

       This man page only documents the hardware-specific features of the liebert driver. For information about the core driver, see nutupsdrv(8).

SUPPORTED HARDWARE

       This driver supports some Liebert UPS equipment with a contact-closure interface. This includes the UPStation GXT2 with their
       contact-closure cable. The smart mode ("Multilink") cable is not supported by this driver.

EXTRA ARGUMENTS

       This driver does not support any extra settings in the ups.conf(5).

BUGS

       This driver does not yet support shutdowns by raising DTR. Be aware that shutdowns are not possible with the stock contact-closure cable.
       You may have to build another cable with DTR connected through to the UPS for it to work.

       There is no way for this driver to detect the hardware or cable. It will start up successfully even if no UPS is present. This is a
       fundamental limitation of any contact-closure driver.

SEE ALSO

   The core driver:
       nutupsdrv(8)

   Internet resources:
       The NUT (Network UPS Tools) home page: http://www.networkupstools.org/

Network UPS Tools						    05/21/2012								LIEBERT(8)

10 More Discussions You Might Find Interesting

1. AIX

Merge NICs

Discussion started by: bong02

2. IP Networking

FreeBSD and two NICs

Discussion started by: ednix

3. Solaris

How many NICS do I have?

Discussion started by: bigapple100

4. Linux

Two NICs one IP address

Discussion started by: wschmied