01-02-2008
From the root login prompt via serial interface I can ping pluto1. I can also ping all the interfaces so it must be doing something internal instead of going out on the network when I execute from the serial CLI login.
Results of ping attempt of router:
root@pluto1 # ping 192.168.1.1
no answer from 192.168.1.1
Results of hostname command:
root@pluto1 # hostname
pluto1
Contents of nsswitch.conf:
passwd: files
group: files
# You must also set up the /etc/resolv.conf file for DNS name
# server lookup. See resolv.conf(4).
hosts: files dns
# Note that IPv4 addresses are searched for in all of the ipnodes databases
# before searching the hosts databases.
ipnodes: files dns
networks: files
protocols: files
rpc: files
ethers: files
netmasks: files
bootparams: files
publickey: files
# At present there isn't a 'files' backend for netgroup; the system will
# figure it out pretty quickly, and won't use netgroups at all.
netgroup: files
automount: files
aliases: files
services: files
printers: user files
auth_attr: files
prof_attr: files
project: files
tnrhtp: files
tnrhdb: files
Would it be as simple as deleting the hostname.* files for IP6?
10 More Discussions You Might Find Interesting
1. AIX
Hi friends,
I installed oracle 10g (10.2.0.2) RAC on 2 IBM p5 570 servers running AIX 5.3ML04 and HACMP5.2 (used Raw devices, not used GPFS). Each server has 4 x 1Gbps ethernet cards (NICs), en0 and en1 for boot address, en2 and en3 for oracle interconnect.
Now i want to merge 2 NICs (en2 and... (1 Reply)
Discussion started by: bong02
1 Replies
2. IP Networking
FreeBSD 4.8, Apache 1.3.27 - two NICs, one with a real-world IP plugged into a switch outside the PIX firewall, the other with a private IP plugged into a switch inside the PIX firewall. Apache listens on both IPs. my domain is mydomain.org.
so in /etc/rc.conf i have something like this (these... (10 Replies)
Discussion started by: ednix
10 Replies
3. Solaris
Hi, is there a way in Solaris 8 to determine how many total NIC's say a Sun Sparc box has installed - plumbed or unplumbed - and find out its capable network speeds and MAC address?
I know ifconfig -a but that only shows the plumbed and used interfaces.
thx
cc (2 Replies)
Discussion started by: bigapple100
2 Replies
4. Linux
I'm looking for a way in RHL 5.1 to use two NICs on one host with two physical IP addresses and map them under one virtual IP address, i.e. NIC 1 10.10.10.1 NIC2 10.10.10.2 VIP 192.168.10.1
Basically I want either one of the NICs to ARP for the VIP. No load balancing required just HA. (2 Replies)
Discussion started by: wschmied
2 Replies
5. IP Networking
hello, i need help on setting my coyote linux, i've working on this for last 5 days, can't get it to work. I've been posting this message to coyote forum, and other linux forum, but haven't get any answer yet. Hope someone here can help me...... please see my attached picture first.
... (0 Replies)
Discussion started by: dlwoaud
0 Replies
6. Programming
Hi,
Can any one tell me why my following program is crashing?
#include <iostream>
using namespace std;
class CA {
public:
const static int i;
};
const int CA::i = 10;
int main() {
int* pi = const_cast<int*>(&CA::i);
*pi = 9;
cout << CA::i << endl;
} (6 Replies)
Discussion started by: royalibrahim
6 Replies
7. Programming
I'm writing a program which uses curl to be run on Linux PCs which will be used by a number of different users. I cannot make the users all install curl on their individual machines, so I have tried to link curl in statically, rather than using libcurl.so. I downloaded the source and created a... (8 Replies)
Discussion started by: BrandonShw
8 Replies
8. Hardware
Hi,
I have to get into BIOS and disable onbaord NICS for an IBM server, can someone please help me out.
I tried hitting F1 when reboot to get into BIOS, but it seems like a setup screen and I dont see any option to disable NICS?
Thanks
Sam (2 Replies)
Discussion started by: sam4919
2 Replies
9. IP Networking
Hi all,
Host - Ubuntu 12.04 desktop 64bit
Virtualizer - Oracle VirtualBox
2 NICs
Where can I find relevant document to set up 2 NICs, one for inward bound and another for outward bound, separate channel, both connected to the same router
Would following document be appropriate for my... (1 Reply)
Discussion started by: satimis
1 Replies
10. UNIX for Dummies Questions & Answers
Hello All,
I have Linux box with two interface cards.
Every card has it's own IP Address and Gateway, IP addresses are from different subnets.
eth0 192.168.1.10/24 GW 192.168.1.1
eth1 192.168.2.10/24 GW 192.168.2.1
Third PC is located in 192.168.13.0/24 network and is trying to access... (2 Replies)
Discussion started by: AndreiM
2 Replies
LEARN ABOUT SUNOS
nss-systemd
NSS-SYSTEMD(8) nss-systemd NSS-SYSTEMD(8)
NAME
nss-systemd, libnss_systemd.so.2 - Provide UNIX user and group name resolution for dynamic users and groups.
SYNOPSIS
libnss_systemd.so.2
DESCRIPTION
nss-systemd is a plug-in module for the GNU Name Service Switch (NSS) functionality of the GNU C Library (glibc), providing UNIX user and
group name resolution for dynamic users and groups allocated through the DynamicUser= option in systemd unit files. See systemd.exec(5) for
details on this option.
This module also ensures that the root and nobody users and groups (i.e. the users/groups with the UIDs/GIDs 0 and 65534) remain resolvable
at all times, even if they aren't listed in /etc/passwd or /etc/group, or if these files are missing.
To activate the NSS module, add "systemd" to the lines starting with "passwd:" and "group:" in /etc/nsswitch.conf.
It is recommended to place "systemd" after the "files" or "compat" entry of the /etc/nsswitch.conf lines so that /etc/passwd and /etc/group
based mappings take precedence.
EXAMPLE
Here is an example /etc/nsswitch.conf file that enables nss-systemd correctly:
passwd: compat mymachines systemd
group: compat mymachines systemd
shadow: compat
hosts: files mymachines resolve [!UNAVAIL=return] dns myhostname
networks: files
protocols: db files
services: db files
ethers: db files
rpc: db files
netgroup: nis
SEE ALSO
systemd(1), systemd.exec(5), nss-resolve(8), nss-myhostname(8), nss-mymachines(8), nsswitch.conf(5), getent(1)
systemd 237 NSS-SYSTEMD(8)