Sponsored Content
Operating Systems Solaris Assigning a static IP to NICs Post 302155016 by theninja on Wednesday 2nd of January 2008 04:51:11 PM
Old 01-02-2008
The output from netstat looks ok, the defaultrouter is set correctly,,,,,hmmmm

Can you ping pluto1? If not,

Check the /etc/nsswitch.conf file, it should show "files" first like so,,,

hosts: files dns
networks: files
ethers: files
netmasks: files

I assume hostname returns pluto1?

You can't ping the router at all?

Do you need IPv4 and IPv6 running? If not, turn off IPv6
 

10 More Discussions You Might Find Interesting

1. AIX

Merge NICs

Hi friends, I installed oracle 10g (10.2.0.2) RAC on 2 IBM p5 570 servers running AIX 5.3ML04 and HACMP5.2 (used Raw devices, not used GPFS). Each server has 4 x 1Gbps ethernet cards (NICs), en0 and en1 for boot address, en2 and en3 for oracle interconnect. Now i want to merge 2 NICs (en2 and... (1 Reply)
Discussion started by: bong02
1 Replies

2. IP Networking

FreeBSD and two NICs

FreeBSD 4.8, Apache 1.3.27 - two NICs, one with a real-world IP plugged into a switch outside the PIX firewall, the other with a private IP plugged into a switch inside the PIX firewall. Apache listens on both IPs. my domain is mydomain.org. so in /etc/rc.conf i have something like this (these... (10 Replies)
Discussion started by: ednix
10 Replies

3. Solaris

How many NICS do I have?

Hi, is there a way in Solaris 8 to determine how many total NIC's say a Sun Sparc box has installed - plumbed or unplumbed - and find out its capable network speeds and MAC address? I know ifconfig -a but that only shows the plumbed and used interfaces. thx cc (2 Replies)
Discussion started by: bigapple100
2 Replies

4. Linux

Two NICs one IP address

I'm looking for a way in RHL 5.1 to use two NICs on one host with two physical IP addresses and map them under one virtual IP address, i.e. NIC 1 10.10.10.1 NIC2 10.10.10.2 VIP 192.168.10.1 Basically I want either one of the NICs to ARP for the VIP. No load balancing required just HA. (2 Replies)
Discussion started by: wschmied
2 Replies

5. IP Networking

I need HELP to Set up Coyote Linux router with 1 static IP & 64 internal static IP

hello, i need help on setting my coyote linux, i've working on this for last 5 days, can't get it to work. I've been posting this message to coyote forum, and other linux forum, but haven't get any answer yet. Hope someone here can help me...... please see my attached picture first. ... (0 Replies)
Discussion started by: dlwoaud
0 Replies

6. Programming

C++ program is crashing on re-assigning const static member variable using an int pointer

Hi, Can any one tell me why my following program is crashing? #include <iostream> using namespace std; class CA { public: const static int i; }; const int CA::i = 10; int main() { int* pi = const_cast<int*>(&CA::i); *pi = 9; cout << CA::i << endl; } (6 Replies)
Discussion started by: royalibrahim
6 Replies

7. Programming

Even the Static cURL Library Isn't Static

I'm writing a program which uses curl to be run on Linux PCs which will be used by a number of different users. I cannot make the users all install curl on their individual machines, so I have tried to link curl in statically, rather than using libcurl.so. I downloaded the source and created a... (8 Replies)
Discussion started by: BrandonShw
8 Replies

8. Hardware

How to get into BIOS and disable NICS?

Hi, I have to get into BIOS and disable onbaord NICS for an IBM server, can someone please help me out. I tried hitting F1 when reboot to get into BIOS, but it seems like a setup screen and I dont see any option to disable NICS? Thanks Sam (2 Replies)
Discussion started by: sam4919
2 Replies

9. IP Networking

Networking 2 NICs

Hi all, Host - Ubuntu 12.04 desktop 64bit Virtualizer - Oracle VirtualBox 2 NICs Where can I find relevant document to set up 2 NICs, one for inward bound and another for outward bound, separate channel, both connected to the same router Would following document be appropriate for my... (1 Reply)
Discussion started by: satimis
1 Replies

10. UNIX for Dummies Questions & Answers

Linux with two NICs

Hello All, I have Linux box with two interface cards. Every card has it's own IP Address and Gateway, IP addresses are from different subnets. eth0 192.168.1.10/24 GW 192.168.1.1 eth1 192.168.2.10/24 GW 192.168.2.1 Third PC is located in 192.168.13.0/24 network and is trying to access... (2 Replies)
Discussion started by: AndreiM
2 Replies
defaultrouter(4)						   File Formats 						  defaultrouter(4)

NAME
defaultrouter - configuration file for default router(s) SYNOPSIS
/etc/defaultrouter DESCRIPTION
The /etc/defaultrouter file specifies a IPv4 host's default router(s). The format of the file is as follows: IP_address ... The /etc/defaultrouter file can contain the IP addresses or hostnames of one or more default routers, with each entry on its own line. If you use hostnames, each hostname must also be listed in the local /etc/hosts file, because no name services are running at the time that defaultrouter is read. Lines beginning with the ``#'' character are treated as comments. The default routes listed in this file replace those added by the kernel during diskless booting. An empty /etc/defaultrouter file will cause the default route added by the kernel to be deleted. Use of a default route, whether received from a DHCP server or from /etc/defaultrouter, prevents a machine from acting as an IPv4 router. You can use routeadm(1M) to override this behavior. FILES
/etc/defaultrouter Configuration file containing the hostnames or IP addresses of one or more default routers. SEE ALSO
in.rdisc(1M), in.routed(1M), routeadm(1M), hosts(4) SunOS 5.10 17 Aug 2004 defaultrouter(4)
All times are GMT -4. The time now is 08:19 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy