01-02-2008
I don't know if the MAC address can failover via IPMP. I am not even sure if you can change the MAC address of a NIC, but if you can, it will have to be via a separate script.
10 More Discussions You Might Find Interesting
1. IP Networking
I've setup Solaris IP Multipathing under Solaris whenever the hardware to do so was available. I find it amazing though that so few places I've worked at don't use it until I arrive. I wanted to find out if I'm running into all the exceptions, or is it really not being used? ... (3 Replies)
Discussion started by: kduffin
3 Replies
2. Solaris
I have solaris 10 sparc. I installed a Qlogic hba card.
This card is connected on a brocade switch and the brocade is connected on 2 different controllers on a Hitachi disk bay.
I formated 2 luns. On my solaris system, i have 4 disk.
How to configure solaris 10 to fix the dual disk view.
... (4 Replies)
Discussion started by: simquest
4 Replies
3. Solaris
Hi,
I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation .
I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2.
Now is it possible to have IP Multipathing on each of the servers as follows ?
... (0 Replies)
Discussion started by: maadhuu
0 Replies
4. Solaris
Dear UNIX Gurus
I need to know how to disable MPXIO feature (Inbuilt multipathing software of Solaris 10) as we are going to implemented iSCSI EMC based SAN. I am bit new to this feature so kindly suggest how to disable it
Regards (4 Replies)
Discussion started by: girish.batra
4 Replies
5. Solaris
Hi friends ,
can anyone provide me the complete steps to configure IPMP in solaris 9 or 10 provided i have two NIC card ?
regards
jagan (4 Replies)
Discussion started by: jaganblore
4 Replies
6. Solaris
Hai
we using emc storage which is conneted to M5000 through san switch.
we asign 13 luns but in server it is showing 22 luns.
i enable the solaris multipathing (MPxIO)
#more /kernel/drv/fp.conf in that file
MPxio-disable=no
#mpathadm list lu
it shows ... (2 Replies)
Discussion started by: joshmani
2 Replies
7. Solaris
Can any one please explain me the concept behind IPMP in solaris clustering.Basic explanation would be really appreciated...
Thanks in Advance
vks (2 Replies)
Discussion started by: vks47
2 Replies
8. Solaris
hi,
just installed solaris 11.1 (11.1.9.5.1) on a sun7410 ZFSSA (x4440 + j4400), but when I enable multipathing with "stmsboot -e", only the 1TB SATA drives inside the j4400 are configured as multipathed vhci / mpxio devices, but the logzillas / ZeusIOPS drives are skipped. the server is... (0 Replies)
Discussion started by: pressy
0 Replies
9. Solaris
hi all,
i start with solaris 11 and i am disapointed by the change on ip managing.
i want to set a ipmp over tow aggregate but i dont find any doc and i am lost with the new commande
switch1
net0 aggregate1 |
net1 aggregate1 |-----|
|... (1 Reply)
Discussion started by: sylvain
1 Replies
10. Solaris
Hi all,
Just a few questions ->
Is an "OFFLINE" interface going back to "ONLINE" consider as a failback by IPMP ?
I have "FAILBACK=no" in my /etc/default/mpathd; however when i do the following
(igb0 and igb7 are in the same ipmp link based group)
q1) why does "if_mpadm -r igb7" cause... (0 Replies)
Discussion started by: javanoob
0 Replies