UNIX command for ethernet cards? Post: 302153977

8 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Adding new Ethernet cards

Hi there, I just installed a Sparc 4-port Ethernet adapter on my sparc 10 and was wondering how on earth I find out what the names of the ports are. It looks like on startup that on SBus1 there is something called qec qe qe qe qe. So I tried to do an IFCONFIG qe0...but had no success. Can anyone...

2. UNIX for Dummies Questions & Answers

SCO Unix and Two Network Cards

Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg Can anyone tell...

3. AIX

PCI Ethernet Cards for IBM RISC 6000 - B50's

I am trying to find PCI Ethernet cards that are compatible with the IBM RISC 6000 - B50 Power PC. None of the regular NIC's seem to have AIX drivers. Does anyone know of AIX drivers for standard PCI Ethernet NIC's or a non IBM NIC that works with the Model B50 at 10/100 MB ?

4. IP Networking

Setup 2 NIC cards in one UNIX system

Hi; I have a UNIX box (SCO 5.0.2) with two (2) NIC cards. One card (NIC1) talks to a network 57.14.65.x/27. The other card NIC2) talks to users on 57.14.103.x and 57.14.105.x with subnet mask of 255.255.0.0. If I set NIC2 to this subnet mask (255.255.0.0) it seems like the NIC traffic is now...

5. Solaris

Command to get the details and number of HBA cards

Hiii... Every one.... I want to know the command to get the details and number of HBA cards attached to a server. I know that we can use "powermt display", but nither my cards are connected to the storage nor powerpath is active. I am using SUN server with Solaris -9. Thanks in...

6. AIX

Idenity no of ethernet cards on the server

How can I identify how many ethernet adapter cards I have on the server from the below ouput ? $>lsdev -Cc adapter | grep ent ent0 Available 06-08 10/100/1000 Base-TX PCI-X Adapter (14106902) ent1 Available 07-08 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902) ent2 ...

7. UNIX for Dummies Questions & Answers

1 Server with 2 ethernet cards IP on seperate network. Possible?

Hi All, I have just setup a webserver running on a linux box. This server has 2 ethernet cards and only 1 is in used now. eg. 192.168.10.1 is my server IP. All users from 192.168.10.X can access my webserver. However, users from another LAN 10.10.10.X are not able to access my webserver. They...

8. Red Hat

Command for viewing hba cards on rhel7

hi all, I am trying to view the hba cards on a rhel7 server (storage says they are there, but I am not seeing them. I tried lspci -nn | grep -i hba lspci |grep qla I tried looking in /sys/class/fc_host.. but it is empty. I am not sure if I am looking in the right spot...

LEARN ABOUT OSF1

ip6_setup

ip6_setup(8)						      System Manager's Manual						      ip6_setup(8)

NAME

       ip6_setup - IPv6 configuration program

SYNOPSIS

       /usr/sbin/ip6_setup

DESCRIPTION

       The ip6_setup utility allows you to configure the IPv6 networking software on your system.

       To run ip6_setup, enter the following command and then answer the questions: # ip6_setup

       You  must know your Internet Protocol Version 6 (IPv6) address. If your network uses subnet routing, you must know the subnet mask for your
       network.  The network manager should be able to provide you with the information that you need.

       After the ip6_setup command completes, the network services on the  system  can	be  restarted  manually  with  the  following  command:  #
       /usr/sbin/rcinet restart

       Before  you  restart  the  network  services  with  the preceding command, warn the users that the network services on the system are being
       removed.  File systems that were not mounted using the /etc/fstab file or the automount command must be unmounted with the unmount command.
       You must remount these file systems using the mount command after the network is started on your system.

       Alternatively, you can reboot the system with the following command: # /usr/sbin/shutdown -r now

FILES

       Specifies  the  host  name  file.  Specifies the environment variables that define the network configuration on your system.  Specifies the
       trusted hosts file.  Specifies the network name file.  Specifies Internet routing information.  Specifies Internet routing information.

SEE ALSO

       Commands: mount(8), rcinet(8)

       Files: gateways(4), hosts(4), hosts.equiv(4), networks(4), routes(4).

       Network Administration

																      ip6_setup(8)