12-19-2007
In general Linux and Solaris and I'm pretty sure most of the BSDs install fine on SATA, I have multiple machines running with SATA only without promblems including the one I am typing this on.
Do you have some kind of unusual SATA controller or Motherboard? Posting your specs would help.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi,
I have two sata hard-disks. Out of those, one is having RHEL5 operating system, and other is having fedora7 operating system.
When I connect the disk with RHEL5 operating system to sata0 port and disk with fedora7 operating system to sata1 port. While booting it shows RHEL5 boot screen,... (3 Replies)
Discussion started by: praveen_b744
3 Replies
2. UNIX for Advanced & Expert Users
trying to setup a sata drive using a sata to scsi adaptor
I have a sata 1TB Deskstar that I had setup before and during shipment from a facilty to another, the disk failed. The handling was not great, lots of throwing boxes, etc. I have a new disk from Hitachi (thankyou Hitachi) anyway, I don't... (1 Reply)
Discussion started by: mndavies
1 Replies
3. Red Hat
Dear All,
Hi,
i am trying to install redhat linux 4 update 4 on HP compaq dx7400 model.
but i stucked up on sata controlar drivers. it is asking for drivers for sata, and not inbuilt in linux cd.
i am trying to find it on net but not succeed.
Thanks
Sandeep D.
Mobile:-9850999505 (0 Replies)
Discussion started by: sdarange
0 Replies
4. UNIX for Dummies Questions & Answers
I am trying to make an application which works on unix to work on linux. I already tried copying the binary files and start it up but I am getting an error stating "Cannot execute binary file". Then I tried to recompile but i am getting an error whenever I tried to recompile. I am getting the... (1 Reply)
Discussion started by: khestoi
1 Replies
5. Hardware
Hello everybody,
I need to connect a laptop 2.5 SATA hard drive to a Desktop board (which uses 3.5' SATA hard drives). I've tried the connectors and they fit excellent in the 2.5 SATA connectors.
The problem is that the laptop hard drive uses 5v and the PC's power source sends 12v. So, my... (4 Replies)
Discussion started by: Zykl0n-B
4 Replies
6. Shell Programming and Scripting
Hi,
I use this command in Linux but if I run the same command does not work in freebsd.
Follow the below command:
Linux works:
sed -e '1731a\' -e '####' squid.conf > squid2.conf ; sed -e '1731a\' -e 'acl TESTE_ip src 192.168.1.1/255.255.255.255' squid2.conf > squid.conf ; sed -e... (7 Replies)
Discussion started by: andreirp
7 Replies
7. Hardware
I have an upgrade path in mind for a new computer that will be stocked with a 2TB SATA 300 hard disk. This is a choice based on information that SATA 300 is not necessarily faster than SATA 600. The upgrade path in a year time or so would then involve the purchase of an SSD that would contain the... (4 Replies)
Discussion started by: figaro
4 Replies
8. SCO
I am very new to SCO Unix so I apologize if this is a easy or dumb question.
I have a 160GB SATA hard drive and SATA CD-ROM drive connected to one of my systems. I have both the drives running in compatibility mode. I also have the hard drive set as a primary master and the CD-ROM drive set as... (10 Replies)
Discussion started by: NPIGuy
10 Replies
9. Shell Programming and Scripting
My script work on Linux but not work in sun os.
my script.
logFiles="sentLog1.log sentLog2.log"
intial_time="0 0"
logLocation="/usr/local/tomcat/logs/"
sleepTime=600
failMessage=":: $(tput bold)Log not update$(tput rmso) = "
successMessage="OK"
arr=($logFiles)... (7 Replies)
Discussion started by: ooilinlove
7 Replies
10. Linux
Hi,
I am using Aitech sata device sil3132, on powerpc mpc8641. The device is pci express msi compatible. I had enabled msi in device tree for powerpc but still its giving me Cannot translate IRQ index 0 and so on messages.
fsl-msi f7f41600.msi: fsl_msi_setup_hwirq: Cannot translate IRQ index 0... (0 Replies)
Discussion started by: shubha_1
0 Replies
SIIS(4) BSD Kernel Interfaces Manual SIIS(4)
NAME
siis -- SiliconImage Serial ATA Host Controller driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device pci
device scbus
device siis
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
siis_load="YES"
The following tunables are settable from the loader(8):
hint.siis.X.msi
controls Message Signaled Interrupts (MSI) usage by the specified controller.
hint.siisch.X.pm_level
controls SATA interface Power Management for the specified channel, allowing some power to be saved at the cost of additional command
latency. Possible values:
0 interface Power Management is disabled (default);
1 device is allowed to initiate PM state change, host is passive.
Note that interface Power Management is not compatible with device presence detection. A manual bus reset is needed on device hot-plug.
hint.siisch.X.sata_rev
setting to nonzero value limits maximum SATA revision (speed). Values 1, 2 and 3 are respectively 1.5, 3 and 6Gbps.
DESCRIPTION
This driver provides the CAM(4) subsystem with native access to the SATA ports of controller. Each SATA port is represented to CAM as a sep-
arate bus with 16 targets. Most of the bus-management details are handled by the SATA-specific transport of CAM. Connected ATA disks are
handled by the ATA protocol disk peripheral driver ada(4). ATAPI devices are handled by the SCSI protocol peripheral drivers cd(4), da(4),
sa(4), etc.
Driver features include support for Serial ATA and ATAPI devices, Port Multipliers (including FIS-based switching), hardware command queues
(31 command per port), Native Command Queuing, SATA interface Power Management, device hot-plug and Message Signaled Interrupts.
Same hardware is also supported by the atasiliconimage driver from ata(4) subsystem. If both drivers are loaded at the same time, this one
will be given precedence as the more functional of the two.
HARDWARE
The siis driver supports the following controllers:
o SiI3124
o SiI3132
o SiI3531
SEE ALSO
ada(4), ata(4), cam(4), cd(4), da(4), sa(4)
HISTORY
The siis driver first appeared in FreeBSD 8.0.
AUTHORS
Alexander Motin <mav@FreeBSD.org>.
BSD
July 18, 2009 BSD