|
|
Sponsored Content
Top Forums
UNIX for Dummies Questions & Answers
Any Linux/Unix work with SATA yet?
Post 302152390 by reborg on Wednesday 19th of December 2007 06:01:34 PM
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi,
I have two sata hard-disks. Out of those, one is having RHEL5 operating system, and other is having fedora7 operating system.
When I connect the disk with RHEL5 operating system to sata0 port and disk with fedora7 operating system to sata1 port. While booting it shows RHEL5 boot screen,... (3 Replies)
Discussion started by: praveen_b744
3 Replies
2. UNIX for Advanced & Expert Users
trying to setup a sata drive using a sata to scsi adaptor
I have a sata 1TB Deskstar that I had setup before and during shipment from a facilty to another, the disk failed. The handling was not great, lots of throwing boxes, etc. I have a new disk from Hitachi (thankyou Hitachi) anyway, I don't... (1 Reply)
Discussion started by: mndavies
1 Replies
3. Red Hat
Dear All,
Hi,
i am trying to install redhat linux 4 update 4 on HP compaq dx7400 model.
but i stucked up on sata controlar drivers. it is asking for drivers for sata, and not inbuilt in linux cd.
i am trying to find it on net but not succeed.
Thanks
Sandeep D.
Mobile:-9850999505 (0 Replies)
Discussion started by: sdarange
0 Replies
4. UNIX for Dummies Questions & Answers
I am trying to make an application which works on unix to work on linux. I already tried copying the binary files and start it up but I am getting an error stating "Cannot execute binary file". Then I tried to recompile but i am getting an error whenever I tried to recompile. I am getting the... (1 Reply)
Discussion started by: khestoi
1 Replies
5. Hardware
Hello everybody,
I need to connect a laptop 2.5 SATA hard drive to a Desktop board (which uses 3.5' SATA hard drives). I've tried the connectors and they fit excellent in the 2.5 SATA connectors.
The problem is that the laptop hard drive uses 5v and the PC's power source sends 12v. So, my... (4 Replies)
Discussion started by: Zykl0n-B
4 Replies
6. Shell Programming and Scripting
Hi,
I use this command in Linux but if I run the same command does not work in freebsd.
Follow the below command:
Linux works:
sed -e '1731a\' -e '####' squid.conf > squid2.conf ; sed -e '1731a\' -e 'acl TESTE_ip src 192.168.1.1/255.255.255.255' squid2.conf > squid.conf ; sed -e... (7 Replies)
Discussion started by: andreirp
7 Replies
7. Hardware
I have an upgrade path in mind for a new computer that will be stocked with a 2TB SATA 300 hard disk. This is a choice based on information that SATA 300 is not necessarily faster than SATA 600. The upgrade path in a year time or so would then involve the purchase of an SSD that would contain the... (4 Replies)
Discussion started by: figaro
4 Replies
8. SCO
I am very new to SCO Unix so I apologize if this is a easy or dumb question.
I have a 160GB SATA hard drive and SATA CD-ROM drive connected to one of my systems. I have both the drives running in compatibility mode. I also have the hard drive set as a primary master and the CD-ROM drive set as... (10 Replies)
Discussion started by: NPIGuy
10 Replies
9. Shell Programming and Scripting
My script work on Linux but not work in sun os.
my script.
logFiles="sentLog1.log sentLog2.log"
intial_time="0 0"
logLocation="/usr/local/tomcat/logs/"
sleepTime=600
failMessage=":: $(tput bold)Log not update$(tput rmso) = "
successMessage="OK"
arr=($logFiles)... (7 Replies)
Discussion started by: ooilinlove
7 Replies
10. Linux
Hi,
I am using Aitech sata device sil3132, on powerpc mpc8641. The device is pci express msi compatible. I had enabled msi in device tree for powerpc but still its giving me Cannot translate IRQ index 0 and so on messages.
fsl-msi f7f41600.msi: fsl_msi_setup_hwirq: Cannot translate IRQ index 0... (0 Replies)
Discussion started by: shubha_1
0 Replies
LEARN ABOUT NETBSD
what-patch
WHAT-PATCH(1) General Commands Manual WHAT-PATCH(1) NAME
what-patch - detect which patch system a Debian package uses SYNOPSIS
what-patch [options] DESCRIPTION
what-patch examines the debian/rules file to determine which patch system the Debian package is using. what-patch should be run from the root directory of the Debian source package. OPTIONS
Listed below are the command line options for what-patch: -h, --help Display a help message and exit. -v Enable verbose mode. This will include the listing of any files modified outside or the debian/ directory and report any additional details about the patch system if available. AUTHORS
what-patch was written by Kees Cook <kees@ubuntu.com>, Siegfried-A. Gevatter <rainct@ubuntu.com>, and Daniel Hahler <ubuntu@thequod.de>, among others. This manual page was written by Jonathan Patrick Davies <jpds@ubuntu.com>. Both are released under the GNU General Public License, version 3 or later. SEE ALSO
The Ubuntu MOTU team has some documentation about patch systems at the Ubuntu wiki: https://wiki.ubuntu.com/PackagingGuide/PatchSystems cdbs-edit-patch(1), dbs-edit-patch(1), dpatch-edit-patch(1) DEBIAN
Debian Utilities WHAT-PATCH(1)