12-17-2007
Quote:
Originally Posted by
rednex
....the user can be informed much earlier that its time to backup this disk.
You should be backing up the disk anyway irrespective of this as this is only one of the many ways your data may become unrecoverable. Power spikes, bearing failures, buggy/malicious software, erroneous deletions etc can all trash your data.
What you are asking for is very low-level and device/manufacturer specific.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi, guys !
Could someone clarify one thing for me:
I start machine from disk0, and want to check the /etc/vfstab on disk1. How do i do it ?
Tried to write:
cd /
mount /dev/dsk/c0t1d0s0 /mnt
But if I do cd /mnt, it is empty. I expected to see disk1 there ? Or am I wrong ?
How do I... (3 Replies)
Discussion started by: DGoubine
3 Replies
2. Filesystems, Disks and Memory
I found a document: Bad block HOWTO for smartmontools
My hard drive is Maxtor:
root]# fdisk -lu /dev/hda
Disk /dev/hda: 81.9 GB, 81964302336 bytes
255 heads, 63 sectors/track, 9964 cylinders, total 160086528 sectors
Units = sectors of 1 * 512 = 512 bytes
Disk identifier: 0x3f4e3f4d
... (0 Replies)
Discussion started by: justinian
0 Replies
3. UNIX for Dummies Questions & Answers
Hi Guys,
I have a failing 4gb (c0t5d0) drive that contains lvol4 -8 on hp-ux. It's not the boot disk but is part of VG00 volume group. Within that group, I have a disk (c0t4d0) of the same size that has 1 lvol on it for swap(4gb) I also have a seperate 1.5 gb swap volume on another physical disk... (1 Reply)
Discussion started by: rees_a
1 Replies
4. Linux
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Discussion started by: shen747
23 Replies
5. Boot Loaders
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
Discussion started by: wljackhero
0 Replies
6. Linux
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
Discussion started by: wljackhero
0 Replies
7. UNIX for Advanced & Expert Users
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
Discussion started by: wljackhero
0 Replies
8. AIX
Hello,
I have DS4000 IBM SAN Storage ( aka FastT Storage )
One of my disks has failed and I had a hot spare disk covering all the arrays. As the disk failed, immediately the hotspare disk took over the failed disk ( see the JPEG in the attachment )
My Question: How can I make the hotspare... (1 Reply)
Discussion started by: filosophizer
1 Replies
9. Shell Programming and Scripting
Hi All,
i am trying to get sectors,cylinders,track..etc information of all present disks out of solaris machine using prtvtoc command .
Output of ptrvtoc command is as below :
bash-3.2# prtvtoc /dev/dsk/c1t0d0s0
* /dev/dsk/c1t0d0s0 partition map
*
* Dimensions:
* 512 bytes/sector... (2 Replies)
Discussion started by: omkar.jadhav
2 Replies
10. Solaris
Hi all,
I have a EFI disk and it is use in zfs pool.
partition> p
Volume: rpool
Current partition table (original):
Total disk sectors available: 1172107117 + 16384 (reserved sectors)
Part Tag Flag First Sector Size Last Sector
0 usr wm ... (8 Replies)
Discussion started by: javanoob
8 Replies
PARTX(8) System Manager's Manual PARTX(8)
NAME
partx - telling the kernel about presence and numbering of on-disk partitions.
SYNOPSIS
partx [-a|-d|-l] [--type TYPE] [--nr M-N] [partition] disk
DESCRIPTION
Given a block device ( disk ) and a partition table type , try to parse the partition table, and list the contents. Optionally add or
remove partitions.
This is not an fdisk - adding and removing partitions is not a change of the disk, but just telling the kernel about presence and numbering
of on-disk partitions.
OPTIONS
-a add specified partitions or read disk and add all partitions
-d delete specified or all partitions
-l list partitions. Note that the all numbers are in 512-byte sectors.
--type TYPE
Specify the partition type -- dos, bsd, solaris, unixware or gpt.
--nr M-N
Specify the range of partitions (e.g --nr 2-4).
SEE ALSO
addpart(8), delpart(8), fdisk(8), parted(8), partprobe(8)
AVAILABILITY
The partx command is part of the util-linux-ng package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux-ng/.
11 Jan 2007 PARTX(8)