Sponsored Content
Operating Systems Linux Debian Kernel source not found. (can't install network card drivers) Post 302150491 by porter on Tuesday 11th of December 2007 04:23:44 PM
Old 12-11-2007
Try

apt-get install linux-source-2.6.18

or

apt-get install linux-source-2.6.18-5
 

6 More Discussions You Might Find Interesting

1. AIX

Hp Laserjet 4600 jetdirct card printr drivers

Iam facing dificulty in installing hp color laserjet 4600 printer in IBM-AIX 5.1. Where i can find a drivers for this printer ,Or pls suggest me another way to get it install this printer Thanx Ravi (2 Replies)
Discussion started by: ravikantchavan
2 Replies

2. Solaris

Unable to install the Network Card

Hi, After I installed Solaris 10 in the Intel platform (chipset 865*) network card was not detected, were shall I get this driver? iam new to Solaris. (2 Replies)
Discussion started by: pravin_2929
2 Replies

3. Solaris

Ethernet card drivers issue...

I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do? Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies

4. Solaris

Network card drivers for solaris?

Hi all, i have configured my solaris 5 .10 for internet connection by editing the files /etc/hosts/,/etc/resolve.config,/etc/defalutrouter and nsswitchconfig . during installation i was not requested for ip adddress even i plugged network cable. am i need to install any network card... (2 Replies)
Discussion started by: srikanthg
2 Replies

5. UNIX for Dummies Questions & Answers

How to install a network card

Hey guys, Sorry, this question might look stupid but I have no idea how to install a network card. My server is a Dell PowerEdge T105 with Debian 5.0 Lenny. My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express. I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies

6. UNIX for Dummies Questions & Answers

How to install kernel source?

During installation of one of driver i needed to Remove any earlier version drivers using make clean -r command. Where i m getting following error. # make clean -r Kernel source is not installed make: *** Error 1 My kernel version # uname -r 2.6.18-128.2.1.4.9.el5xen Where... (4 Replies)
Discussion started by: pinga123
4 Replies
DEBCONF-APT-PROGRESS(1) 					      Debconf						   DEBCONF-APT-PROGRESS(1)

NAME
debconf-apt-progress - install packages using debconf to display a progress bar SYNOPSIS
debconf-apt-progress [--] command [args ...] debconf-apt-progress --config debconf-apt-progress --start debconf-apt-progress --from waypoint --to waypoint [--] command [args ...] debconf-apt-progress --stop DESCRIPTION
debconf-apt-progress installs packages using debconf to display a progress bar. The given command should be any command-line apt frontend; specifically, it must send progress information to the file descriptor selected by the "APT::Status-Fd" configuration option, and must keep the file descriptors nominated by the "APT::Keep-Fds" configuration option open when invoking debconf (directly or indirectly), as those file descriptors will be used for the debconf passthrough protocol. The arguments to the command you supply should generally include -y (for apt-get or aptitude) or similar to avoid the apt frontend prompting for input. debconf-apt-progress cannot do this itself because the appropriate argument may differ between apt frontends. The --start, --stop, --from, and --to options may be used to create a progress bar with multiple segments for different stages of installation, provided that the caller is a debconf confmodule. The caller may also interact with the progress bar itself using the debconf protocol if it so desires. debconf locks its config database when it starts up, which makes it unfortunately inconvenient to have one instance of debconf displaying the progress bar and another passing through questions from packages being installed. If you're using a multiple-segment progress bar, you'll need to eval the output of the --config option before starting the debconf frontend to work around this. See "EXAMPLES" in the EXAMPLES section below. OPTIONS
--config Print environment variables necessary to start up a progress bar frontend. --start Start up a progress bar, running from 0 to 100 by default. Use --from and --to to use other endpoints. --from waypoint If used with --start, make the progress bar begin at waypoint rather than 0. Otherwise, install packages with their progress bar beginning at this "waypoint". Must be used with --to. --to waypoint If used with --start, make the progress bar end at waypoint rather than 100. Otherwise, install packages with their progress bar ending at this "waypoint". Must be used with --from. --stop Stop a running progress bar. --no-progress Avoid starting, stopping, or stepping the progress bar. Progress messages from apt, media change events, and debconf questions will still be passed through to debconf. --dlwaypoint percentage Specify what percent of the progress bar to use for downloading packages. The remainder will be used for installing packages. The default is to use 15% for downloading and the remaining 85% for installing. --logfile file Send the normal output from apt to the given file. --logstderr Send the normal output from apt to stderr. If you supply neither --logfile nor --logstderr, the normal output from apt will be discarded. -- Terminate options. Since you will normally need to give at least the -y argument to the command being run, you will usually need to use -- to prevent that being interpreted as an option to debconf-apt-progress itself. EXAMPLES
Install the GNOME desktop and an X window system development environment within a progress bar: debconf-apt-progress -- aptitude -y install gnome x-window-system-dev Install the GNOME, KDE, and XFCE desktops within a single progress bar, allocating 45% of the progress bar for each of GNOME and KDE and the remaining 10% for XFCE: #! /bin/sh set -e case $1 in '') eval "$(debconf-apt-progress --config)" "$0" debconf ;; debconf) . /usr/share/debconf/confmodule debconf-apt-progress --start debconf-apt-progress --from 0 --to 45 -- apt-get -y install gnome debconf-apt-progress --from 45 --to 90 -- apt-get -y install kde debconf-apt-progress --from 90 --to 100 -- apt-get -y install xfce4 debconf-apt-progress --stop ;; esac RETURN CODE
The exit code of the specified command is returned, unless the user hit the cancel button on the progress bar. If the cancel button was hit, a value of 30 is returned. To avoid ambiguity, if the command returned 30, a value of 3 will be returned. AUTHORS
Colin Watson <cjwatson@debian.org> Joey Hess <joeyh@debian.org> 2011-06-22 DEBCONF-APT-PROGRESS(1)
All times are GMT -4. The time now is 03:10 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy