I tried to telnet to my Sun server (E250) but I received the error message :
"Network error: Connection reset by peer".
I was able to ping my server. And, I had already commented off "CONSOLE=/dev/console" in /etc/default/login.
But, if I rlogin from all other servers, it works.
Is there... (2 Replies)
Hi
I am fresher in Virtualisation in solaris 10.I need to know how to install and configure guest OS, I have a server Sun T2000 with solaris 10 OS BASE.
How to install logical domain, what are the prerequest for installing l domain
can some one guide me what are the basic requirement to... (2 Replies)
Hello Folks,
I am having trouble to login to rsc or serial console of V890.
The rsc2.2.3 has been configured with required parameters, resetrs and even rebooted. When serial port is connected to laptop, The hyper terminal does not get the console or POSt messages when the server is rebooting... (8 Replies)
I have a sun fire v240 server.
The output of prtdiag -v shows a failed fan.
There are 3 fans for cooling system board.
There is 1 fan for each of the powersupply (There are 2 powersupplies)
From the below output how do i know which fan is bad and whats its location... (3 Replies)
I have a problem,
I have been installing Redhat Interprise Linux on X4100 M2 Server, when system is reboot after install, the server is restart (reboot) again (alias unlimited).
The bios system show message error "Multi-bit ECC Error" and "bank interleave requested but not enable"
I have... (5 Replies)
cat note
Hi Sun Solaris Experts,
When I try to install Solaris 8 10/00 OS via the Solaris 8 Installation Disk on our Sun Fire V490 Server using the command , I get:
boot: cannot open kernel/sparcv9/unix
which means it can't find the unix kernel file on the installation disk .
By the way, I... (5 Replies)
Hi Solaris/Unix Experts,
I've installed Oracle Solaris 10 1/13 on a Sun Fire V490 Server via its external Serial Port using a Cisco Console Cable connected to my Laptop PC running SecureCRT terminal emulation software emulating VT100 Terminal.
The Sun Fire V490 server has two on-board... (1 Reply)
Discussion started by: ssabet
1 Replies
LEARN ABOUT DEBIAN
vdetelweb
VDETELWEB(1) General Commands Manual VDETELWEB(1)NAME
vdetelweb - Virtual Distributed Ethernet Telnet and/or Web management module
SYNOPSIS
vdetelweb [ --web ] [ --telnet ] [ --nodename nodename ] [ --daemon ] [ --rcfile rcfile ] mgmt_socket
DESCRIPTION
vdetelweb implements a tiny telnet server and/or a tiny web server for the remote management of a VDE2 switch.
OPTIONS -w, --web
start the web server. At least one of --web or --telnet must be set.
-t, --telnet
start the telnet server. At least one of --web or --telnet must be set.
-n, --nodename nodename
specify the nodename as seen from remote connections (e.g. in the command prompt or in the web page title). uname nodename is used
when this option is not specified.
-d, --daemon
run as a daemon, using syslog for logging.
-f, --rcfile rcfile
rc file to set the initial switch configuration. When not specified, vdetelweb searches for ~/.vde/vdetelwebrc and /etc/vde/vdetel-
webrc. At leas one rc file must exist and be readable.
-h, --help
print help. please use it for a more complete list of options.
mgmt_socket
is the managemnt socket used to communicate with the vde_switch. (This option must match the path used in the -M option for the
vde_switch).
NOTICE
Virtual Distributed Ethernet is not related in any way with www.vde.com ("Verband der Elektrotechnik, Elektronik und Informationstechnik"
i.e. the German "Association for Electrical, Electronic & Information Technologies").
SEE ALSO vde_switch(1), vde_plug(1), vdeq(1). dpipe(1). unixterm(1).
AUTHOR
VDE is a project by Renzo Davoli <renzo@cs.unibo.it>
Virtual Distributed Ethernet June 16, 2008 VDETELWEB(1)