11-28-2007
unable to telnet from win xp to sun fire v880 server
Hi everybody
i am trying to telnet to sun server from win xp machine but getting message "x21 error connection closed by remote user". i had make changes in /etc/default/login & /etc/fuser file still i have not getting telnet access. my win xp machines ip is 10.205.121.177 & sun server ip is 10.205.119.246
plz help me
Regards
prakash
8 More Discussions You Might Find Interesting
1. IP Networking
I tried to telnet to my Sun server (E250) but I received the error message :
"Network error: Connection reset by peer".
I was able to ping my server. And, I had already commented off "CONSOLE=/dev/console" in /etc/default/login.
But, if I rlogin from all other servers, it works.
Is there... (2 Replies)
Discussion started by: dawn_lwf
2 Replies
2. Solaris
Hi
I am fresher in Virtualisation in solaris 10.I need to know how to install and configure guest OS, I have a server Sun T2000 with solaris 10 OS BASE.
How to install logical domain, what are the prerequest for installing l domain
can some one guide me what are the basic requirement to... (2 Replies)
Discussion started by: solaris8in
2 Replies
3. Solaris
Hello Folks,
I am having trouble to login to rsc or serial console of V890.
The rsc2.2.3 has been configured with required parameters, resetrs and even rebooted. When serial port is connected to laptop, The hyper terminal does not get the console or POSt messages when the server is rebooting... (8 Replies)
Discussion started by: defflepord
8 Replies
4. Solaris
I have a sun fire v240 server.
The output of prtdiag -v shows a failed fan.
There are 3 fans for cooling system board.
There is 1 fan for each of the powersupply (There are 2 powersupplies)
From the below output how do i know which fan is bad and whats its location... (3 Replies)
Discussion started by: Tirmazi
3 Replies
5. Solaris
==============================
ALOM BOOTMON v1.3.1
ALOM Build Release: 001
Reset register: f0000000 EHRS ESRS LLRS SWRS
ALOM POST 1.0
Dual Port Memory Test, PASSED.
TTY External - Internal Loopback Test
TTY External - Internal Loopback Test, PASSED.
TTYC - Internal Loopback Test
TTYC -... (4 Replies)
Discussion started by: Sameer Naik
4 Replies
6. Hardware
I have a problem,
I have been installing Redhat Interprise Linux on X4100 M2 Server, when system is reboot after install, the server is restart (reboot) again (alias unlimited).
The bios system show message error "Multi-bit ECC Error" and "bank interleave requested but not enable"
I have... (5 Replies)
Discussion started by: hhaswan
5 Replies
7. Solaris
cat note
Hi Sun Solaris Experts,
When I try to install Solaris 8 10/00 OS via the Solaris 8 Installation Disk on our Sun Fire V490 Server using the command , I get:
boot: cannot open kernel/sparcv9/unix
which means it can't find the unix kernel file on the installation disk .
By the way, I... (5 Replies)
Discussion started by: ssabet
5 Replies
8. Solaris
Hi Solaris/Unix Experts,
I've installed Oracle Solaris 10 1/13 on a Sun Fire V490 Server via its external Serial Port using a Cisco Console Cable connected to my Laptop PC running SecureCRT terminal emulation software emulating VT100 Terminal.
The Sun Fire V490 server has two on-board... (1 Reply)
Discussion started by: ssabet
1 Replies
LEARN ABOUT DEBIAN
rxtelnet
RXTELNET(1) BSD General Commands Manual RXTELNET(1)
NAME
rxtelnet -- start a telnet and forward X-connections.
SYNOPSIS
rxtelnet [-l username] [-k] [-t telnet_args] [-x xterm_args] [-K kx_args] [-w term_emulator] [-b telnet_program] [-n] [-v] host [port]
DESCRIPTION
The rxtelnet program starts an xterm window with a telnet to host host. From this window you will also be able to run X clients that will be
able to connect securely to your X server. If port is given, that port will be used instead of the default.
If setting up the X forwarding failes, rxtelnet will still telnet in to the remote host, but without X forwarding.
The supported options are:
-l Log in on the remote host as user username.
-k Disables keep-alives.
-t Send telnet_args as arguments to telnet.
-x Send xterm_args as arguments to xterm.
-X Send kx_args as arguments to kx.
-w Use term_emulator instead of xterm.
-b Use telnet_program instead of telnet.
-n Do not start any terminal emulator.
-v Be verbose.
EXAMPLE
To login from host foo (where your display is) to host bar, you might do the following.
1. On foo: rxtelnet bar
2. You will get a new window with a telnet to bar. In this window you will be able to start X clients.
SEE ALSO
kx(1), rxterm(1), telnet(1), tenletxr(1), kxd(8)
KTH_KRB March 7, 2004 KTH_KRB