11-23-2007
hi new2ss,
I'm having the same problem, please tell me how did you solve it?
Thanks
9 More Discussions You Might Find Interesting
1. Solaris
Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1...
But instead the ext PCI takes precedence in the order and the Net0 becomes... (3 Replies)
Discussion started by: incredible
3 Replies
2. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
3. UNIX for Dummies Questions & Answers
Hi Guys,
is there a way to send traffic coming from the source iface (eth0, eth1)? i need to test traffic that will come from both eth0 and eth1 from a Linux box.
Thanks,
Martin (0 Replies)
Discussion started by: mdap
0 Replies
4. Linux
Hi,
I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0
and my requirement is 100mbps full duplex.
Regards,
Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies
5. UNIX for Dummies Questions & Answers
Right now I have a computer that I want to use as the monitor for my network. It's currently running Windows 7, and so as I understand it the NIC won't monitor all the traffic on the network. So my question is, if I install Linux on this computer will I be able to force the NIC card into... (1 Reply)
Discussion started by: iJeydon
1 Replies
6. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
7. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
8. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
CLP(1) General Commands Manual CLP(1)
NAME
clp - linear program solver
SYNOPSIS
clp filename [ options ] solutionfile
DESCRIPTION
This manual page documents briefly the clp command.
clp -- interface to the coin linear programming solver. clp solves the following linear optimization program:
minimize c^t x
such that: row_lb <= Ax <= row_ub
column_lb <= x <= column_ub
OPTIONS
When no options are given clp enters the interactive command line mode. Otherwise the program enters a batch mode, for which a summary of
options is included below. For a complete description, see /usr/share/doc/coinor-libclp-doc.
-help Show summary of options.
-primalsimplex
solve the problem using the primal simplex method
-dualsimplex
solve the problem using the dual simplex method
-maximize
maximize the problem
SEE ALSO
glpsol(1),dsdp5(1)
This program is fully documented in the accompanying html documentation which can be found in /usr/share/doc/coinor-libclp-doc if the
coinor-libclp-doc package is installed.
AUTHOR
clp was written by John J. Forrest <jjforre@us.ibm.com> et.al.
This manual page was written by Soeren Sonnenburg <sonne@debian.org>, for the Debian project (but may be used by others).
May 7, 2008 CLP(1)