11-14-2007
Yep do diskinfo on the raw device (and then note that disk vendors call 1 MB = 1000000 bytes).
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello,
I need explanations about physical disks and physical volumes. What is the difference between these 2 things?
In fact, i am trying to understand what the AIX lspv2command does.
Thank you in advance. (2 Replies)
Discussion started by: VeroL
2 Replies
2. Solaris
Friends,
I have an 80 GB HDD, but I wish to know if there is a direct command in Solaris 10 to find out the size of my hard disk (similar to fdisk -l in Linux).
Thank you
saagar (3 Replies)
Discussion started by: saagar
3 Replies
3. Filesystems, Disks and Memory
Hi,
I am trying to find the reliability of 'vmstat -d' for showing the actual physical writes on sectors on hard disk.
Can anyone please tell me if the numbers in the "sectors" field under "read" or "write" headers show a count of the actual write commands sent to disk from the low level... (2 Replies)
Discussion started by: jake24
2 Replies
4. Filesystems, Disks and Memory
How do I check for physical damage on red hat linux hard disks? I tried smartctl /dev/sdb but it came back so fast saying it was ok. Is there a better linux command to check for bad sectors or physical disks in linux? Is there a good way such as with parted or something else? I normally in HP... (4 Replies)
Discussion started by: taekwondo
4 Replies
5. Solaris
I have a Sun T5120, and I want to programmatically determine how much RAM it has.
# uname -a
SunOS myhost 5.10 Generic_141444-09 sun4v sparc SUNW,SPARC-Enterprise-T5120
The box has 64Gb; I tried prtdiag and prtconf, but they give me bogus info
prtconf gives me:
# prtconf |grep -i... (12 Replies)
Discussion started by: thomn8r
12 Replies
6. Linux
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Discussion started by: shen747
23 Replies
7. AIX
This is the report I got running the comand rptconf, but I would like to know what is the capacity of the disks installed into our server power 6 with AIX
System Model: IBM,7778-23X
Machine Serial Number: 1066D5A
Processor Type: PowerPC_POWER6
Processor Implementation Mode: POWER 6... (6 Replies)
Discussion started by: cucosss
6 Replies
8. UNIX for Dummies Questions & Answers
Hi,
Using Redhat, how do I display total hard disk size? I know how to do that in Solaris, you can type, format. It will show how big the disks are.
This is what I did so for.
$ df -t ext3 -h
Filesystem Size Used Avail Use% Mounted on
/dev/mapper/VolGroup00-LogVol00
... (1 Reply)
Discussion started by: samnyc
1 Replies
9. UNIX for Advanced & Expert Users
Hello,
in one default UFS filesystem we have 8K block size (bsize) and 1K fragmentsize (fsize). At this scenary I thought all "FileSytem IO" will be 8K (or greater) but never smaller than the fragment size (1K). If a UFS fragment/blocksize is allwasy several ADJACENTS sectors on disk (in a ... (4 Replies)
Discussion started by: rarino2
4 Replies
10. Solaris
Hi, looking to upgrade memory on a pair of T5220's from 32GB to 64GB. Cannot determine current DIMM size and slots used. i.e. not sure if Qty 16 x 2GB or Qty 8 x 4GB. If there are no empty slots, i need to go with higher density DIMMs and retire exsisting the 2GB prtdiag follows.
#... (3 Replies)
Discussion started by: edrew
3 Replies
RAW(8) System Administration RAW(8)
NAME
raw - bind a Linux raw character device
SYNOPSIS
raw /dev/raw/raw<N> <major> <minor>
raw /dev/raw/raw<N> /dev/<blockdev>
raw -q /dev/raw/raw<N>
raw -qa
DESCRIPTION
raw is used to bind a Linux raw character device to a block device. Any block device may be used: at the time of binding, the device
driver does not even have to be accessible (it may be loaded on demand as a kernel module later).
raw is used in two modes: it either sets raw device bindings, or it queries existing bindings. When setting a raw device, /dev/raw/raw<N>
is the device name of an existing raw device node in the filesystem. The block device to which it is to be bound can be specified either
in terms of its major and minor device numbers, or as a path name /dev/<blockdev> to an existing block device file.
The bindings already in existence can be queried with the -q option, which is used either with a raw device filename to query that one
device, or with the -a option to query all bound raw devices.
Unbinding can be done by specifying major and minor 0.
Once bound to a block device, a raw device can be opened, read and written, just like the block device it is bound to. However, the raw
device does not behave exactly like the block device. In particular, access to the raw device bypasses the kernel's block buffer cache
entirely: all I/O is done directly to and from the address space of the process performing the I/O. If the underlying block device driver
can support DMA, then no data copying at all is required to complete the I/O.
Because raw I/O involves direct hardware access to a process's memory, a few extra restrictions must be observed. All I/Os must be cor-
rectly aligned in memory and on disk: they must start at a sector offset on disk, they must be an exact number of sectors long, and the
data buffer in virtual memory must also be aligned to a multiple of the sector size. The sector size is 512 bytes for most devices.
OPTIONS
-q, --query
Set query mode. raw will query an existing binding instead of setting a new one.
-a, --all
With -q , specify that all bound raw devices should be queried.
-h, --help
Display help text and exit.
-V, --version
Display version information and exit.
BUGS
The Linux dd(1) command should be used without the bs= option, or the blocksize needs to be a multiple of the sector size of the device
(512 bytes usually), otherwise it will fail with "Invalid Argument" messages (EINVAL).
Raw I/O devices do not maintain cache coherency with the Linux block device buffer cache. If you use raw I/O to overwrite data already in
the buffer cache, the buffer cache will no longer correspond to the contents of the actual storage device underneath. This is deliberate,
but is regarded either a bug or a feature depending on who you ask!
NOTES
Rather than using raw devices applications should prefer open(2) devices, such as /dev/sda1, with the O_DIRECT flag.
AUTHOR
Stephen Tweedie (sct@redhat.com)
AVAILABILITY
The raw command is part of the util-linux package and is available from https://www.kernel.org/pub/linux/utils/util-linux/.
util-linux August 1999 RAW(8)