11-08-2007
Bind zone transfer recategorises zone file?
Hi,
I have a primary/slave Bind 9 setup running on a Solaris 10 platform. Everything is hunky dorey, except for when I make a zone file change and up the serial the file that is transferred to the slave looses all its comments, and the entries are place in alphabetical order.
I administer many Bind setup's, and I have never experienced anything like this in the past. Has anyone had any experience with this issue?
Thanks in advance, Tom.
9 More Discussions You Might Find Interesting
1. IP Networking
Hi all,
How to deny any zone transfer out of my host??? bind 8.2.3
Thank you all,
Regards
:D (2 Replies)
Discussion started by: solvman
2 Replies
2. Shell Programming and Scripting
Dear all,
Did anyone in this forum know site that offer free DNS zone transfer? if anyon know, please reply my message.
Thanks (0 Replies)
Discussion started by: unknown2205
0 Replies
3. Solaris
Hi Greetings...
I have an issue in connecting the zone from outside the network and it is because of default gateway. I can ping default gateway from inside the zone and not able to ping from global zone due to different VLAN issue. If i add two different gateways and restart network services,... (2 Replies)
Discussion started by: vvpotugunta
2 Replies
4. Solaris
I have two physical servers, with zones that mount local storage.
We were using "raw device" in the zonecfg to point to a metadevice on the global zone (it was not mounted in the global zone at any point).
It failed to mount on every boot because the directory existed in the zone.
I... (6 Replies)
Discussion started by: BG_JrAdmin
6 Replies
5. Solaris
Hi All ,
I have 2 DNS servers (BIND 9.6.1 -Solaris 10) .Its configured as master ,slave serves .Now i am recieving error messages related to zone transfer in both the servers as mentioned below .
Primar Server
named: client x.x.x.x#40825: transfer of './IN': sending zone data: ran... (1 Reply)
Discussion started by: sandeep.tk
1 Replies
6. Solaris
can some one help me out as it is showing 2 different time zones in global zone and nonglobal zone .In global zone it is showing in GMT while in nonglobal zone i it showing as PDT.
System in running with solaris 10 (3 Replies)
Discussion started by: ravijanjanam12
3 Replies
7. Ubuntu
I have a couple of zone conf files for the BIND server.
There are some records that contains the "IN" statement and some do not.
But anyway this works.
So my question is what this "IN" is intended for?
Here is the zone file example:
ORIGIN .
$ttl 60
example.com. IN SOA ... (4 Replies)
Discussion started by: andriesh
4 Replies
8. UNIX for Advanced & Expert Users
Dear all,
recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes.
I did the following:
host1:
$ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed
$ zpool export zone1
host2:
$ zpool... (2 Replies)
Discussion started by: custos
2 Replies
9. Solaris
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
TCOM(4) BSD Kernel Interfaces Manual TCOM(4)
NAME
tcom -- multiplexing serial communications interface
SYNOPSIS
For 4-port TC-400 series boards:
tcom0 at isa? port 0x100 irq 5
com2 at tcom? slave ?
com3 at tcom? slave ?
com4 at tcom? slave ?
com5 at tcom? slave ?
For 8-port TC-800 series boards:
tcom0 at isa? port 0x100 irq 5
com2 at tcom? slave ?
com3 at tcom? slave ?
com4 at tcom? slave ?
com5 at tcom? slave ?
com6 at tcom? slave ?
com7 at tcom? slave ?
com8 at tcom? slave ?
com9 at tcom? slave ?
DESCRIPTION
The tcom driver provides support for the Byte Runner Technologies TC-400 and TC-800 series boards that multiplex together up to four or eight
EIA RS-232C (CCITT V.28) communications interfaces.
Each tcom device is the master device for up to eight com devices. The kernel configuration specifies these com devices as slave devices of
the tcom device, as shown in the synopsis. The slave ID given for each com device determines which bit in the interrupt multiplexing regis-
ter is tested to find interrupts for that device. The port specification for the tcom device is used to compute the base addresses for the
com subdevices and the port for the interrupt multiplexing register.
Not all possible configuration options are currently supported (for example, speeds beyond 115200 baud are not currently supported).
FILES
/dev/tty??
SEE ALSO
com(4)
HISTORY
The tcom driver was written by Jukka Marin.
BSD
May 20, 1998 BSD