Sponsored Content
Operating Systems SCO Continueing relyability problems with SCO 6.0 on Dell Poweredge 1800 with PERC DC4. Post 302144085 by frederik1 on Tuesday 6th of November 2007 06:29:36 AM
Old 11-06-2007
Hi All,

I've added the KHZ=100 parameter to /stand/boot, and fsck-ed all filesystems as suggested in this newsgroup:
OpenServer 6.0.0 hangs randomly. Please help! - comp.unix.sco.misc | Google Groups
They described a simular problem with a HP Proliant G5 there (seems to me a very rugged machine, can't imagine that such hardware easily causes problems)
The machine is put into the rack again and turned on, and I hope this cured my problem.
Any way if there are more suggestions they are welcome.

Frederik
 

8 More Discussions You Might Find Interesting

1. Linux Benchmarks

Dell Dual Xeon PowerEdge 4600

Notes: System Configuration: Dell Computer Corporation PowerEdge 4600 (4 X Intel(R) XEON(TM) CPU 2.00GHz 1988.782 MHz) hyperthreaded System clock frequency: 99.0827 MHz Memory size (approximate): 2559 Megabytes ========================= CPUs ======================== CPU # CPU... (0 Replies)
Discussion started by: tnorth
0 Replies

2. Linux Benchmarks

Dell Poweredge 2400 / 533

CPU/Speed: Dual PIII 533 Ram: 256Mb PC133 Motherboard: Unknown, Intel Chipset Cache: 256k on board Controller: PARC Raid 2/Si, AIC-7880U Disk: 30Gb RAID 5 Load: 1 user. Clean boot, init 5 but X-Windows not loaded. Kernel: See Benchmarks. pgms: gcc 3.2.3 ... (2 Replies)
Discussion started by: Garp
2 Replies

3. Solaris

Installing Solaris 10 on Dell PowerEdge 2800

hi, i am trying to install solaris 10 (on 4 cd's downloaded from the sun website) on my dell poweredge 2800 server. 2 xeon processors, 2GB of RAM and 2 NICS, 73 GB SCSI (maxtor ultra320, 3.5 series), i can give more details on request... the installation crashes when trying to detect the NICS... (0 Replies)
Discussion started by: xinugeek
0 Replies

4. Red Hat

Installing RedHat 8.0 onto Dell PowerEdge SC1425 - hdc: status error: status = 0x58

I have successfully installed RedHat 8.0 onto a Dell PowerEdge SC1425 today. This server has two SATA hard drives, and an IDE DVD-ROM drive. Using the following kernel parameters, i successfully installed across both hard drives from CD: ide0=0x1f0,0x3f6,14 vga=791 resolution=1024x768 expert... (5 Replies)
Discussion started by: fishsponge
5 Replies

5. Filesystems, Disks and Memory

Linux and Dell 1500sc Poweredge Server

Does anybody no how to get around the fact that the Red Hat installation does not see the SCSI hard drives. It lets you manually pick the proper device, but still fails saying no drive detected (or something to that effect). I was going to install windows 2003 Server and use VMware...but again,... (1 Reply)
Discussion started by: Fatflea
1 Replies

6. UNIX for Dummies Questions & Answers

Stange problem Dell PowerEdge 1950/ Boradcom Netextreme NIC

I have 2 Dell Poweredge 1950 servers running . I have been having intermittent performance issues with the NIC cards on one of them. The two servers are identical and are running the same operating system. The server that has the issue is on the DMZ on a a static IP and is hosting a website. ... (0 Replies)
Discussion started by: skotapal
0 Replies

7. Programming

/dev/mem on Dell Poweredge

Hi, I have a C++ program to access /dev/mem and retrieve details like Vendor, Manufacturer details of the motherboard. This works fine on all the machines except for on Dell Poweredge 2850,1950... machines. I receive a 'EFAULT' when I try to access /dev/mem on these servers. I suspect some... (1 Reply)
Discussion started by: ragisreekanth
1 Replies

8. SCO

Dell PowerEdge 2600 tape backup

I was asked to get a Dell PowerEdge 2600 server, out of warranty, running SCO 3.2v5.06 to perform a full backup. I spent hours researching and preparing a strategy only to fail on-site. The only device names in /dev for a tape drive were /dev/xStp0 /dev/xcdt0 /dev/xct0 ... (6 Replies)
Discussion started by: ezlarry
6 Replies
MODERATORS(5)							File Formats Manual						     MODERATORS(5)

NAME
moderators - mail addresses for moderated Usenet newsgroups DESCRIPTION
The GetModeratorAddress(3) routine reads the file /etc/news/moderators to determine how to reach the moderator of a newsgroup. This is used by inews(1) when an unapproved local posting is made to a moderated newsgroup. The file is read until a match is found. Blank lines and lines starting with a number sign (``#'') are ignored. All other lines should consist of two fields separated by a colon. The first field is a wildmat(3)-style pattern. If it matches the name of the newsgroup, then the second field is taken to be a format string for sprintf(3). This string should have at most one %s parameter, which will be given the name of the newsgroup with periods transliterated to dashes. Here is a sample file: foo.important:announce-request@foo.com foo.*:%s@mailer.foo.com gnu.*:%s@prep.ai.mit.edu *:%s@uunet.uu.net Using the above file, postings to the moderated newsgroup in the left column will be sent to the address shown in the right column: foo.important announce-request@foo.com foo.x.announce foo-x-announce@mailer.foo.com gnu.emacs.sources gnu-emacs-sources@prep.ai.mit.edu comp.sources.unix comp-sources-unix@uunet.uu.net HISTORY
Written by Rich $alz <rsalz@uunet.uu.net> for InterNetNews. This is revision 1.15, dated 1996/09/06. SEE ALSO
inews(1), inn.conf(5), libinn(3), wildmat(3). MODERATORS(5)
All times are GMT -4. The time now is 11:07 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy