11-06-2007
Hi All,
I've added the KHZ=100 parameter to /stand/boot, and fsck-ed all filesystems as suggested in this newsgroup:
OpenServer 6.0.0 hangs randomly. Please help! - comp.unix.sco.misc | Google Groups
They described a simular problem with a HP Proliant G5 there (seems to me a very rugged machine, can't imagine that such hardware easily causes problems)
The machine is put into the rack again and turned on, and I hope this cured my problem.
Any way if there are more suggestions they are welcome.
Frederik
8 More Discussions You Might Find Interesting
1. Linux Benchmarks
Notes:
System Configuration: Dell Computer Corporation PowerEdge 4600 (4 X Intel(R) XEON(TM) CPU 2.00GHz
1988.782 MHz) hyperthreaded
System clock frequency: 99.0827 MHz
Memory size (approximate): 2559 Megabytes
========================= CPUs ========================
CPU # CPU... (0 Replies)
Discussion started by: tnorth
0 Replies
2. Linux Benchmarks
CPU/Speed: Dual PIII 533
Ram: 256Mb PC133
Motherboard: Unknown, Intel Chipset
Cache: 256k on board
Controller: PARC Raid 2/Si, AIC-7880U
Disk: 30Gb RAID 5
Load: 1 user. Clean boot, init 5 but X-Windows not loaded.
Kernel: See Benchmarks.
pgms: gcc 3.2.3
... (2 Replies)
Discussion started by: Garp
2 Replies
3. Solaris
hi, i am trying to install solaris 10 (on 4 cd's downloaded from the sun website) on my dell poweredge 2800 server. 2 xeon processors, 2GB of RAM and 2 NICS, 73 GB SCSI (maxtor ultra320, 3.5 series), i can give more details on request...
the installation crashes when trying to detect the NICS... (0 Replies)
Discussion started by: xinugeek
0 Replies
4. Red Hat
I have successfully installed RedHat 8.0 onto a Dell PowerEdge SC1425 today. This server has two SATA hard drives, and an IDE DVD-ROM drive.
Using the following kernel parameters, i successfully installed across both hard drives from CD:
ide0=0x1f0,0x3f6,14 vga=791 resolution=1024x768 expert... (5 Replies)
Discussion started by: fishsponge
5 Replies
5. Filesystems, Disks and Memory
Does anybody no how to get around the fact that the Red Hat installation does not see the SCSI hard drives. It lets you manually pick the proper device, but still fails saying no drive detected (or something to that effect). I was going to install windows 2003 Server and use VMware...but again,... (1 Reply)
Discussion started by: Fatflea
1 Replies
6. UNIX for Dummies Questions & Answers
I have 2 Dell Poweredge 1950 servers running . I have been having intermittent performance issues with the NIC cards on one of them. The two servers are identical and are running the same operating system. The server that has the issue is on the DMZ on a a static IP and is hosting a website. ... (0 Replies)
Discussion started by: skotapal
0 Replies
7. Programming
Hi,
I have a C++ program to access /dev/mem and retrieve details like Vendor, Manufacturer details of the motherboard. This works fine on all the machines except for on Dell Poweredge 2850,1950... machines.
I receive a 'EFAULT' when I try to access /dev/mem on these servers.
I suspect some... (1 Reply)
Discussion started by: ragisreekanth
1 Replies
8. SCO
I was asked to get a Dell PowerEdge 2600 server, out of warranty, running SCO 3.2v5.06 to perform a full backup. I spent hours researching and preparing a strategy only to fail on-site.
The only device names in /dev for a tape drive were
/dev/xStp0
/dev/xcdt0
/dev/xct0
... (6 Replies)
Discussion started by: ezlarry
6 Replies
BTSCO(4) BSD Kernel Interfaces Manual BTSCO(4)
NAME
btsco -- Bluetooth SCO Audio
SYNOPSIS
btsco* at bthub?
audio* at audiobus?
DESCRIPTION
The btsco driver provides support for Bluetooth SCO Audio devices through the audio(4) driver.
The btsco driver must be configured at run time with the btdevctl(8) program. The following properties are used by the btsco driver during
autoconfiguration:
local-bdaddr
Local device address.
remote-bdaddr
Remote device address.
service-name
The btsco driver matches the 'HF' and 'HSET' services. For the 'HF' service, the btsco device will, on open(2), listen for incom-
ing connections from the remote device. Otherwise, btsco will attempt to initiate a connection to the remote device.
rfcomm-channel
This integer value is not used directly, but will be stored and passed via the BTSCO_INFO ioctl as below:
SCO connections require a baseband connection between the two devices before they can be created. The btsco driver does not create this, but
can provide information to facilitate an application setting up a control channel prior to use, via the BTSCO_INFO ioctl(2) call on the mixer
device, which returns a btsco_info structure as follows:
#include <dev/bluetooth/btsco.h>
struct btsco_info {
bdaddr_t laddr; /* controller bdaddr */
bdaddr_t raddr; /* headset bdaddr */
uint8_t channel; /* RFCOMM channel */
int vgs; /* mixer index speaker */
int vgm; /* mixer index mic */
};
#define BTSCO_INFO _IOR('b', 16, struct btsco_info)
The btsco driver can be configured to act in Connect or Listen mode. In Connect mode, the btsco driver will initiate a connection to the
remote device on an open(2) call, whereas in Listen mode, open(2) will block until the remote device initiates the connection.
SEE ALSO
bthset(1), ioctl(2), audio(4), bluetooth(4), bthub(4), btdevctl(8)
HISTORY
The btsco driver was written for NetBSD 4.0 by Iain Hibbert under the sponsorship of Itronix, Inc.
BUGS
btsco takes no notice of the HCI Voice Setting in the Bluetooth controller, and this must be 0x0060 (the default) as alternate values are
currently unsupported.
BSD
October 4, 2006 BSD