11-02-2007
urgent......Serial port
I think my serial port(on board) is not working ......
because when I am running same code on two machines its working good....but when my system comes into picture ....it doesnt show any output comming from serial port..........
can anybody tell me how to configure my serial port.........or to check it is installed on ot or not...........
moreover I had inserted another card having two serial ports.....
info about card:::::::::::::::::::is here
05:04.0 Serial controller: Timedia Technology Co Ltd PCI2S550 (Dual 16550 UART) (rev 01) (prog-if 02 [16550])
Subsystem: Timedia Technology Co Ltd Unknown device 4037
Flags: stepping, medium devsel, IRQ 10
I/O ports at 1100 [size=32]
but how to configure/install ....this card.
I am using fedora core 6
thanks & regards.........
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
We're running SCO Unix Openserver 5.05 and I'm having trouble with serial communication between the com2 serial port and a handheld device. Downloading data from Unix to the handheld works perfectly, but the other way around creates a major problem. I don't know whether it's a buffer overflow or... (1 Reply)
Discussion started by: Aretha
1 Replies
2. Linux
Hi All,
I am a begineer in Linux, I have 4 ports and 3 are operational port 1,port 2 and port 4 (when I plug in serial device I can see it working) but port 3 seems it is not working.
I am sure the hardware is fine.
when I give command
dmesg | grep tty
I get,
serial 8250:ttyS0 at... (0 Replies)
Discussion started by: vr_82
0 Replies
3. Programming
I am developing an application in c with Linux OS, where a radio modem working at baud rate 9600 will be attached to PC on serial port. More than four such units will be communicating at one time, so there may be jamming or data corruption. Each module will be transmitting Data packets less than... (2 Replies)
Discussion started by: raj8109
2 Replies
4. Solaris
Hi,
I am working with solaris 9,SUN-Blade-100 and I want to communicate with the Serial port.To check whether the port is working or not.I write code and when I execute the file,then I got the output--
According to this,serial port is not found.can anyone please tell me how to configure the... (1 Reply)
Discussion started by: smartgupta
1 Replies
5. Programming
Hello!
Can someone advice me which method I will use if I want to communicate with device via RS232 serial port with this requirements:
1. Serial port is opened in non-canonical mode.
2. All the time I need to check is there something to read.
3. If I have to write something I need to write it... (6 Replies)
Discussion started by: jvrlic
6 Replies
6. UNIX for Dummies Questions & Answers
A neighbour's Ubuntu 10.04 machine has five serial ports, one on the motherboard and four on a PCI card. However, only four cards are showing:
# dmesg | grep tty
console enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
... (2 Replies)
Discussion started by: dotancohen
2 Replies
7. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
8. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
9. Web Development
I am trying to write to a serial port and capture the reponse in a file -
adduser ethan dialout
The user `ethan' is already a member of `dialout'
root@meow:/home/ethan# ls -l /dev/ttyS0
crw-rw-r-- 1 ethan dialout 4, 64 Oct 7 20:55 /dev/ttyS0
$fh1 = fopen("/dev/ttyS0", "w+");... (74 Replies)
Discussion started by: Meow613
74 Replies
10. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
UMCS(4) BSD Kernel Interfaces Manual UMCS(4)
NAME
umcs -- USB support for serial adapters based on the MCS7820 and MCS7840 chips
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device usb
device ucom
device umcs
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
umcs_load="YES"
DESCRIPTION
The umcs driver provides support for various multiport serial adapters based on the MosCom MCS7820 and MCS7840 chips. They are 2- or 4-port
adapters with full-featured 16550-compatible UARTs and very flexible baud generators. Also, these chips support RS422/RS485 and IrDA opera-
tions.
The device is accessed through the ucom(4) driver which makes it behave like a tty(4).
Different ports on device are presented as sub-units, like /dev/ttyU0.1 and /dev/ttyU0.2.
HARDWARE
The umcs driver was tested on the following adapters:
o ST Lab U-360 two-port serial USB adapter
o ST Lab U-400 four-port serial USB adapter
SEE ALSO
tty(4), ucom(4), usb(4)
HISTORY
The umcs driver appeared in ports since December of 2010.
AUTHORS
The umcs driver was written by Lev Serebryakov <lev@FreeBSD.org>.
BUGS
This driver doesn't support access to any fine tunes of chip, like RS522/RS485 mode, non-standard baudrates, etc.
BSD
February 25, 2012 BSD