10-18-2007
I just went through the same thing on my Sunblade 100 (same box). If you look at the riser where the IDE cable plugs into, there's a 2nd connector under it. You can hook you boot drive to IDE 0 and your CDROM and 2nd drive to IDE 1. Use standard IDE ribbon cables. also, don't for get the jumpers on the 2nd drive must be set as slave. Restart back to your original settings, make sure your box woeks and then go step by step setting up the drive. also, at the ok prompt, run reset-all and then probe-ide to see if your drives show up.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I would like to upgrade the memory in my Sun Blade 150 workstation. In reading through Sun's Blade 150 DIMM Installation Guide, it indicates that the memory must be "certified by Sun for the Sun Blade 150 system."
Does anyone know if any SDRAM, PC133 • CL=2 • Unbuffered • ECC • 133MHz • 3.3V ... (2 Replies)
Discussion started by: here2learn
2 Replies
2. UNIX for Dummies Questions & Answers
Hi, I am new to UNIX. I have a Sun Blade 150 worksation. I used a Dell monitor and Dell keyboard as input and output devices. However, workstation always told me that keyboard couldn't be found. I used Dell keyboard with USB and Dell keyboard with series connector. It all didn't work. Please help... (10 Replies)
Discussion started by: duke0001
10 Replies
3. Solaris
We had to replace a hard drive in one of our Sun Blade 150s, but now it hangs during the Jumpstart. It will show 1 or 2 Timeout for ARP/RARP messages and then start the spinning numbers. It always stops at 2ae00 and just hangs there.
We have 1 combined jumpstart server and it is also our NIS+... (5 Replies)
Discussion started by: stottsja
5 Replies
4. Solaris
Hi,
I have a Solaris 8.0 BLADE 150 machine. I have an onboard graphics alongwith an addon XVR500 graphics card. Now, when I use the motherboard graphics, I am not able to login to the XWINDOWS terminal, instead it stays on the console.
But, if I insert the monitor cable to the XVR500 port,... (2 Replies)
Discussion started by: angshuman_ag
2 Replies
5. Solaris
I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05.
I have just noticed /bin/sun now returns false, rather than true. See below.
$ uname -a
SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100
$ /bin/sparc &&... (1 Reply)
Discussion started by: apmcd47
1 Replies
6. Solaris
Hello,
Ive just aquired a blade 150 off ebay.Im new to suns and are having a problem getting it to boot off the cdrom.Openboot continuously tries to do a network boot and I cant enter any commands.Im using an average pc keyboard and it definetly works.Thanks for any help.:wall: (3 Replies)
Discussion started by: chucky
3 Replies
7. Solaris
Hello,
I cant get my blade box to boot off the harddrive after installing solaris 10.I can get to a root prompt after issuing "boot cdrom -s".I tried booting off disk0 and disk1,but I get "the file just loaded does not seem to be executable".Thanks for any help.:wall: (4 Replies)
Discussion started by: chucky
4 Replies
8. Solaris
Hi everybody,
I'm having big troubles in installing Solaris 8 on a Sun Blade 150.
Here are some system specs:
Sun Blade 150 (UltraSPARC-IIe 550MHz)
RAM: 256MB
OBP 4.10.6 2003/06/06 12:30
POST 2.0.1 2001/08/23 17:13
When I try to boot from Solaris 8 CD with boot cdrom or... (10 Replies)
Discussion started by: Vortigern
10 Replies
9. Solaris
Hi,
I'm using Solaris 8 on a Blade 1500.
I know that IDE drives are limited to around 120GB, but I was told that it's possible to use larger drives with the only caveat that the available size will be that 120 (or is it 128?) GB size.
But when I try, format shows only very low sizes, like... (2 Replies)
Discussion started by: BobSol8
2 Replies
10. Solaris
hello
i have a forte gamma camera Philips device . and its a medical device. this medical device is came with sun blade 150 pc and pegasys is printed on the sun blade pc .the problem is when i switched the power on , the sun blade runs and a white screen appear with the information about the... (6 Replies)
Discussion started by: moh_abaloo
6 Replies
LEARN ABOUT DEBIAN
f1tattoo
f1tattoo(1) f1tattoo 0.7 f1tattoo(1)
NAME
f1tattoo - disc T@2 feature for Yamaha F1 CD-RW devices
SYNOPSIS
f1tattoo [-l] [-h]
f1tattoo -d DEVICE [-c] [-s] [--tattoo-test]
f1tattoo -d DEVICE --tattoo-raw <file.raw>
f1tattoo -d DEVICE --tattoo-png <file.png>
DESCRIPTION
f1tattoo is the linux console tool to use the Yamaha disc T@2 feature. You won't get satisfying results on Phtalocyanin dye.
FEATURES
You can disc T@2 with these drives:
Yamaha F1 CD-RW, Yamaha F1DX
DEVICE
can be an IDE, SCSI, SATA, USB or FireWire connected optical drive. Not all SATA controller support all Plextor features.
Linux:
/dev/hdX: IDE device
/dev/scdX: Linux 2.4: SATA, SCSI, USB device, or IDE device via ide-scsi emulation
/dev/srX: Linux 2.6: IDE device via new ATA layer, SCSI or USB device
OpenBSD/NetBSD:
/dev/rcdX
FreeBSD:
/dev/cd: SCSI device
/dev/acd: ATA device
MacOS X:
/dev/disk:
win32:
C:,D:,E:, ... X:,Y:,Z:
OPTIONS
-l, --scanbus
scan busses for all available CD and DVD devices.
-h, --help
help. show available options.
-c, --current
show current drive settings of selected device
-s, --supported
show supported features of selected device
--tattoo-test
write DiscT@2 test image
--tattoo-raw tattoo.raw
write DiscT@2 using raw data from tattoo.raw file
--tattoo-png tattoo.png
write DiscT@2 using png image from tattoo.png file check if f1tattoo compiled with png support using --help option
-v, --verbose
give verbose output
EXAMPLES
f1tattoo -l
list all available CD- and DVD-devices
f1tattoo -d /dev/hdc --tattoo-raw filename.raw
writes DiscT@2 using filename.raw file on media in device /dev/hdc
please report man page improvements to T.Maguin@web.de
Gennady ShultZ Kozlov 10. April, 2009 f1tattoo(1)