Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Problem with a Network Interface
Operating Systems AIX Problem with a Network Interface Post 302139902 by aldowsary on Tuesday 9th of October 2007 09:20:39 PM
Old 10-09-2007
How to solve the problem above? Or how can I delete the interface in proper way & create again?
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

network interface problem

Hi expert, Need some help on network interface issue.. I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies

2. Solaris

network interface problem solaris 2.5

Hi guys, Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot). I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies

3. UNIX for Dummies Questions & Answers

Multi Network card interface problem

My system info is show below:- #uname -a SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500 and I have two network card as shown below:- #ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies

4. Solaris

Network interface problem

Hi i have replace a NIC card on solaris 10 when i give the following command ifconfig -a it just show the lo0 (only loop back with inet 127.0.0.1) when i give the following command to config the interface, ifconfig elxl0 plumb ifconfig: plumb: elxl0: no such interface please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies

5. Solaris

Network interface problem

HI, genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex genunix: WARNING: ce0: fault detected external to device; service degraded genunix: WARNING: ce0: xcvr addr:0x01 - link down genunix: NOTICE: ce0: fault cleared external to device; service available genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies

6. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

7. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies

8. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

LEARN ABOUT SUSE

clp

CLP(1)							      General Commands Manual							    CLP(1)

NAME

       clp - linear program solver

SYNOPSIS

       clp filename [ options ] solutionfile

DESCRIPTION

       This manual page documents briefly the clp command.

       clp -- interface to the coin linear programming solver. clp solves the following linear optimization program:

	   minimize	 c^t x
	   such that:	 row_lb <= Ax <= row_ub
			 column_lb <= x <= column_ub

OPTIONS

       When  no options are given clp enters the interactive command line mode.  Otherwise the program enters a batch mode, for which a summary of
       options is included below.  For a complete description, see /usr/share/doc/coinor-libclp-doc.

       -help  Show summary of options.

       -primalsimplex
	      solve the problem using the primal simplex method

       -dualsimplex
	      solve the problem using the dual simplex method

       -maximize
	      maximize the problem

SEE ALSO

       glpsol(1),dsdp5(1)

       This program is fully documented in the accompanying html documentation which can  be  found  in  /usr/share/doc/coinor-libclp-doc  if  the
       coinor-libclp-doc package is installed.

AUTHOR

       clp was written by John J. Forrest <jjforre@us.ibm.com> et.al.

       This manual page was written by Soeren Sonnenburg <sonne@debian.org>, for the Debian project (but may be used by others).

								   May	7, 2008 							    CLP(1)
All times are GMT -4. The time now is 01:28 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy