10-08-2007
I invoked the following command to set the interface down:
>> ifconfig fcs2 inet down
After that I could not return it UP again neither using command line nor SMIT.
This used this interface to connect to another server directly using Fiber (Back-to-Back).
Also when I tried to remove this interface and create again I could not.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
2. Solaris
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies
3. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
4. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
5. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
6. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
7. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
8. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT OPENSOLARIS
ifparse
ifparse(1M) System Administration Commands ifparse(1M)
NAME
ifparse - parse ifconfig command line
SYNOPSIS
/sbin/ifparse [-fs] addr_family commands
DESCRIPTION
Use the ifparse command to parse the ifconfig(1M) command line options and output substrings, one per line, as appropriate. If no options
are specified, ifparse returns the entire ifconfig command line as a series of substrings, one per line.
OPTIONS
The ifparse command supports the following options:
-f Lists only substrings of the ifconfig command line that are relevant to IP network multipath failover
-s Lists only substrings of the ifconfig command line that are not relevant to IP network multipath failover
OPERANDS
The ifparse command does not support the interface operand of the ifconfig command.
EXAMPLES
Example 1 Parsing Command Line Options Relevant to Failover
The following example shows the use of the ifparse command to parse the command line options relevant to IP network multipath failover:
example# ifparse -f inet 1.2.3.4 up group one addif 1.2.3.5 -failover up
set 1.2.3.4 up
Example 2 Parsing Command Line Options That Are Not Relevant to Failover
The following example shows the use of the ifparse command to parse the command line options that are not relevant to IP network multipath
failover:
example# ifparse -s inet 1.2.3.4 up group one addif 1.2.3.5 -failover up
group one
addif 1.2.3.5 -failover up
Example 3 Parsing the Command Line For All Options
The following example shows the use of the ifparse command to parse the command line for all ifconfig options:
example# ifparse inet 1.2.3.4 up group one addif 1.2.3.5 -failover up
group one
set 1.2.3.4 up
addif 1.2.3.5 -failover up
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsr |
+-----------------------------+-----------------------------+
|Stability Level |Obsolete |
+-----------------------------+-----------------------------+
SEE ALSO
ifconfig(1M), attributes(5)
DIAGNOSTICS
usage: -fs <addr_family> <commands>
Description:
This message indicates an invalid command line.
ifparse: Not enough space
Description:
This message indicates insufficient memory.
ifparse: dhcp not supported for inet6
Description:
DHCP operations are not supported for the inet6 address family.
ifparse: Operation <operation> not supported for <addr_family>
Description:
Most operations cannot be used with all address families. For example, the broadcast operation is not supported on the inet6 address
family.
ifparse: no argument for <operation>
Description:
Some operations, for example broadcast, require an argument.
NOTES
The ifparse command is classified as an obsolete interface. It will likely be removed in a future release. You should not develop applica-
tions that depend upon this interface.
SunOS 5.11 9 May 2001 ifparse(1M)