10-08-2007
I know this sounds like a windows help desk solution but does the device normally come up after a reboot? (hint hint)
Oh, and why did you set it down?
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
2. Solaris
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies
3. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
4. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
5. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
6. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
7. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
8. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT FREEBSD
altera_atse
ALTERA_ATSE(4) BSD Kernel Interfaces Manual ALTERA_ATSE(4)
NAME
atse -- driver for the Altera Triple-Speed Ethernet MegaCore
SYNOPSIS
device atse
options ATSE_CFI_HACK
In /boot/device.hints:
hint.atse.0.at="nexus0"
hint.atse.0.maddr=0x7f007000
hint.atse.0.msize=0x540
hint.atse.0.rc_irq=1
hint.atse.0.rx_maddr=0x7f007500
hint.atse.0.rx_msize=0x8
hint.atse.0.rxc_maddr=0x7f007520
hint.atse.0.rxc_msize=0x20
hint.atse.0.tx_irq=2
hint.atse.0.tx_maddr=0x7f007400
hint.atse.0.tx_msize=0x8
hint.atse.0.txc_maddr=0x7f007420
hint.atse.0.txc_msize=0x20
hint.e1000phy.0.at="miibus0"
hint.e1000phy.0.phyno=0
DESCRIPTION
The atse device driver provides support for the Altera Triple-Speed Ethernet MegaCore.
HARDWARE
The current version of the atse driver supports the Ethernet MegaCore as described in version 11.1 of Altera's documentation when the device
is configured with internal FIFOs.
MAC SELECTION
The default MAC address for each atse interface is derived from a value stored in cfi(4) flash. The value is managed by the atsectl(8) util-
ity.
Only a single MAC address may be stored in flash. If the address begins with the Altera prefix 00:07:ed and ends in 00 then up to 16
addresses will be derived from it by adding the unit number of the interface to the stored address. For other prefixes, the address will be
assigned to atse0 and random addresses will be used for other interfaces. If the stored address is invalid, for example all zero's, multi-
cast, or the default address shipped on all DE4 boards (00:07:ed:ff:ed:15) then a random address is generated when the device is attached.
SEE ALSO
miibus(4), netintro(4), ifconfig(8)
Triple-Speed Ethernet MegaCore Function User Guide, Altera Corporation, November 2011.
HISTORY
The atse device driver first appeared in FreeBSD 10.0.
AUTHORS
The atse device driver and this manual page were developed by SRI International and the University of Cambridge Computer Laboratory under
DARPA/AFRL contract (FA8750-10-C-0237) (``CTSRD''), as part of the DARPA CRASH research programme. This device driver was written by Bjoern
A. Zeeb.
BUGS
The atse driver only supports a single configuration of the MegaCore as installed on the Terasic Technologies Altera DE4 Development and Edu-
cation Board.
Only gigabit Ethernet speeds are currently supported.
BSD
May 21, 2014 BSD