Yes. pppd automatically adds a default gateway in the way you said. So I have:
On Linux, traceroute shows nothing, it "hangs"... Also a simple ping to the RAS server isn't working. On Windows, tracert works and I see packets going through the server (10.74.49.22).
Are there any of you who have a description which can
help me to make a callback on AIX.
My userīs call in by a telefonnumber at I want AIX to
disconnect the line and make a callback to the user
who had logged on AIX.
The advantage of this is we have security on who we allow to call our... (2 Replies)
Hi guys,
sorry for asking noob question.
When do we really need to add a static route on the server?
I encounter this situation whereby a client trigger a network packet to the destination but the destination does not know how to return the traffic back to the client (source).
The issue was... (4 Replies)
Hi,
I have a system with network interfaces en0 and en1
en0:
physical ip: 1.1.1.10
virtual ip1: 192.168.100.11
virtual ip2: 192.168.100.12
en1:
physical ip: 1.1.1.20
virtual ip1: 192.168.100.20
virtual ip2: 192.168.100.21
default gateway ist 192.168.100.254
when I open a... (12 Replies)
Hi all!
I have a problem.I access to AIX server via SSH,then i use command 'route -q', after that i can't connect to AIX server.Please help me to fix this problem.
Thanks & Best Regards (1 Reply)
I try to delete the route on one of the server
But I am not able to do it
its show the error
# route delete 10.1.88.0 10.37.201.33
delete host 10.1.88.0: gateway 10.37.201.33: not in table
If I add the route also its shows the error message
# route add -net 10.1.88.0 10.37.201.33
add net... (5 Replies)
I am trying to connect to Windows server via Linux server through a script and run two commands " cd and ls " But its giving me error saying " could not start the program" followed by the command name i specify e g : "cd"
i am trying in this manner "
ssh username@servername "cd... (5 Replies)
I have to write a shell script in my current linux server and I have to connect to a different server then do sudo login and finally run some scripts residing in a particular directory and get results back. I am starting to write my shell script as below but after I do ssh login it prompts for... (2 Replies)
Hi my name is Manju.
->I have configure the two way authentication on my linux server.
->Now I am able to apply two way authenticator on particuler user.
->Now I want to map this linux server to my AD server.
->Kindly tell me how to map AD(Active Directory) with this linux server.
... (0 Replies)
Discussion started by: manjusharma128
0 Replies
LEARN ABOUT FREEBSD
traceroute6
TRACEROUTE6(8) BSD System Manager's Manual TRACEROUTE6(8)NAME
traceroute6 -- print the route IPv6 packets will take to a network node
SYNOPSIS
traceroute6 [-adIlnNrvU] [-f firsthop] [-g gateway] [-m hoplimit] [-p port] [-q probes] [-s src] [-w waittime] [-A as_server] target
[datalen]
DESCRIPTION
The traceroute6 utility uses the IPv6 protocol hop limit field to elicit an ICMPv6 TIME_EXCEEDED response from each gateway along the path to
some host.
The only mandatory parameter is the destination host name or IPv6 address. The default probe datagram carries 12 bytes of payload, in addi-
tion to the IPv6 header. The size of the payload can be specified by giving a length (in bytes) after the destination host name.
Other options are:
-a Turn on AS# lookups for each hop encountered.
-A as_server
Turn on AS# lookups and use the given server instead of the default.
-d Debug mode.
-f firsthop
Specify how many hops to skip in trace.
-g gateway
Specify intermediate gateway (traceroute6 uses routing header).
-I Use ICMP6 ECHO instead of UDP datagrams.
-l Print both host hostnames and numeric addresses. Normally traceroute6 prints only hostnames if -n is not specified, and only numeric
addresses if -n is specified.
-m hoplimit
Specify maximum hoplimit, up to 255. The default is 30 hops.
-n Do not resolve numeric address to hostname.
-N Use a packet with no upper layer header for the probes, instead of UDP datagrams.
-p port
Set UDP port number to port.
-q probes
Set the number of probe per hop count to probes.
-r Bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly-connected net-
work, an error is returned. This option corresponds to the SO_DONTROUTE socket option; it can be used to ping a local host through
an interface that has no route through it (e.g., after the interface was dropped by a routing daemon).
-s src Src specifies the source IPv6 address to be used.
-U Use UDP datagrams for the probes. This is the default.
-v Be verbose.
-w waittime
Specify the delay time between probes.
This program prints the route to the given destination and the round-trip time to each gateway, in the same manner as traceroute.
Here is a list of possible annotations after the round-trip time for each gateway:
!N Destination Unreachable - No Route to Host.
!P Destination Unreachable - Administratively Prohibited.
!S Destination Unreachable - Not a Neighbour.
!A Destination Unreachable - Address Unreachable.
! This is printed if the hop limit is <= 1 on a port unreachable message. This means that the packet got to the destination, but
that the reply had a hop limit that was just large enough to allow it to get back to the source of the traceroute6. This was
more interesting in the IPv4 case, where some IP stack bugs could be identified by this behaviour.
EXIT STATUS
The traceroute6 utility will exit with 0 on success, and non-zero on errors.
SEE ALSO ping(8), ping6(8), traceroute(8)HISTORY
The traceroute6 utility first appeared in WIDE hydrangea IPv6 protocol stack kit.
BSD August 24, 2009 BSD