09-27-2007
Quote:
Originally Posted by
vntiger
And I have no idea about my Graphic Adapter. How can I check that?
Can you open the box and see what it says on the board?
I'm sure there is an elegant way to find out whats on the PCI bus, does the "dmesg" output give any clues?
10 More Discussions You Might Find Interesting
1. SCO
Can i change the password on the SCO GUI interface login page and if so how?
When I try to login it just goes right back to the login screen. If anyone has any suggestions, please reply. :confused: (3 Replies)
Discussion started by: qphillips
3 Replies
2. Linux
hi
iam installed mandriva spring 2009
iam unble to login into gui using root
how to enable it
where the settings are stored (5 Replies)
Discussion started by: seshumohan
5 Replies
3. Solaris
I have 2 queries:
1.how do we monitor failed GUI logins...? I think the /var/adm/loginlog will log
only failed logins happened at /dev/console and virtual terminals..
2.How to use cron scheduler to display a message when a user is working in GUI Terminal window irrespective of in which... (1 Reply)
Discussion started by: saagar
1 Replies
4. UNIX for Advanced & Expert Users
Hi,
When I installed Ubuntu on my laptop, I had chosen "automatic login" . So i was not asked ofr username and password everytime I switched on. I later wanted to change the settings. So I went to systems-->administration-->login window-->security. There I disabled automatic login and I reboot the... (3 Replies)
Discussion started by: vishwamitra
3 Replies
5. Solaris
I have a Sun Ultra 45 that was working perfectly until i upgraded it to Update 9 with a zfs filesystem. The box is sparc based and has an internal video card. When i boot it up, i receive an X server error and, while checking /var/dt/Xerrors, the following message is displayed
Fatal server... (9 Replies)
Discussion started by: goose25
9 Replies
6. Fedora
Hi all,
I am able to login via putty to a fedora 10 workstation.
But when i try to login via physical screen connected to workstation, it just gives me a blank screen and i cant see any options to enter username and passwd. How do i get the physical GUI to work.
$ who -r
... (4 Replies)
Discussion started by: lramsb4u
4 Replies
7. AIX
If I login to one of our AIX 6.1 servers using SSH via PuTTY and I issue the who -a or w command I cannot see my session, although if I login via TELNET I can.
Why is this?
SSH:
root#> who
root#> w
08:06PM up 40 days, 27 mins, 0 users, load average: 0.05, 0.12, 0.14
User tty login@ idle... (1 Reply)
Discussion started by: deepinsight
1 Replies
8. Solaris
Solaris machine is at # prompt not able to login in GUI mode :
I want to login solaris server in GUI mode from # prompt.
---------- Post updated 12-30-11 at 11:36 AM ---------- Previous update was 12-29-11 at 02:23 PM ----------
Hi,
Please send me some guidelines regarding this....
as... (2 Replies)
Discussion started by: sunray
2 Replies
9. UNIX for Dummies Questions & Answers
I am not too new with linux. Since I installed a new version (2011) of Mandriva, I am unable to login via the gui (I'm currently using the live version of the same dvd free with Linux Format mag). I can login from a console as it has picked up the previous version's /home, but when I try to login... (2 Replies)
Discussion started by: richardmellersh
2 Replies
10. Shell Programming and Scripting
hii all,
I am unable to login into GUI mode in solaris 10. It is only prompting me to command mode credentials not going further to GUI mode.. Please help..
Thanks & regards,
Bhagi (3 Replies)
Discussion started by: bhargav90
3 Replies
LEARN ABOUT REDHAT
pcitweak
PCITWEAK(1) General Commands Manual PCITWEAK(1)
NAME
pcitweak - read/write PCI config space
SYNOPSIS
pcitweak -l
pcitweak -r PCI-ID [-b|-h] offset
pcitweak -w PCI-ID [-b|-h] offset value
DESCRIPTION
Pcitweak is a utility that can be used to examine or change registers in the PCI configuration space. On most platfoms pcitweak can only
be run by the root user.
OPTIONS
-l Probe the PCI buses and print a line for each detected device. Each line contains the bus location (bus:device:function), chip
vendor/device, card (subsystem) vendor/card, revision, class and header type. All values printed are in hexadecimal.
-r PCI-ID
Read the PCI configuration space register at offset for the PCI device at bus location PCI-ID. PCI-ID should be given in the form
bus:device:function, with each value in hexadecimal. By default, a 32-bit register is read.
-w PCI-ID
Write value to the PCI configuration space register at offset for the PCI device at bus location PCI-ID. PCI-ID should be given in
the form bus:device:function, with each value in hexadecimal. By default, a 32-bit register is written.
-b Read or write an 8-bit value (byte).
-h Read or write a 16-bit value (halfword).
SEE ALSO
scanpci(1)
AUTHORS
David Dawes (dawes@xfree86.org).
XFree86 Version Version 4.3.0 PCITWEAK(1)