09-19-2007
configuring 2-gateways in linux
Hi,
I want to configure 2-gateways in Linux .
Please tell me how I can achieve this. I am accesing 2-internet
connection through these 2-gateways. So I am looking that
if 1-gets down then also other one is working.
Regards
JAGDISH
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I cannot change my gateway. I have five locations (simulated) and i try to ping another of my locations but it says host unreachable and it is showing the gateway as the host i'm pinging withs ip address. I have tried the route command but I couldn't get it to work. Any suggestions on how to... (2 Replies)
Discussion started by: Deuce
2 Replies
2. IP Networking
Hi
does anybody know how we can add more than one ip for NIC(in Redhat Linux 7.2)?
i usually do it by using this command
ifconfig eth0 add <ip addresss> netmask <..............> up
or ;
ip address add 192.168.20.1/24 dev eth0
or
adding it manually to file in... (12 Replies)
Discussion started by: hessam
12 Replies
3. Linux
Had problems in configuring USB memory stick in RHL 9.
Please assist.
With regards,
Kungra. (1 Reply)
Discussion started by: kungra2006
1 Replies
4. Solaris
Hi ......
I'm trying to configure my Solaris servers with only one NIC card to have 2 IP addresses as well as 2 different default gateways.
( NOT to be confused with multi-pathing - with 2 physical IPs & 1 virtual ip)
Thanks,
Remi (1 Reply)
Discussion started by: Remi
1 Replies
5. UNIX for Dummies Questions & Answers
configuring NTP in Solaris/Windows/Linux environment. Can anybody please explain the below table to monitor NTP daemon status
This contains many columns like remote,refid,st....various values corresponding to those columns
If possible provide me any link to study about... (1 Reply)
Discussion started by: sgand
1 Replies
6. Red Hat
Hi All
when I give the command,
$ ping <hostname>
I get the following error
ping: unknown host <hostname>
I have checked in the following files,
/etc/sysconfig/network
/etc/hosts
/etc/resolv.conf
/etc/nsswitch.conf
Every where in these files host name and IP address are given... (2 Replies)
Discussion started by: nagapradeep
2 Replies
7. BSD
I have a web server running FreeBSD 7.2, i have configured two NICs in the following way:
fxp0: 200.14.xxx.254
sk0: 200.12.xxx.4
gateway: 200.14.xxx.1
both ip addresses are public but only those requests to fxp0 are successful.
I have tried configuring nat and binat in sk0 but it... (4 Replies)
Discussion started by: edgarvm
4 Replies
8. IP Networking
i have a linux server runnig oracle applications.
i need to access this server from putty using ssh through internet.
i did by registering my static ip with the dnydns.org and i am able to connect to the server.
but now there is no security to authenticate any user as any one knowing the... (6 Replies)
Discussion started by: u.n.i.x
6 Replies
9. Infrastructure Monitoring
I am trying to enabling SNMP access and trap forwarding for Linux(RHEL5) using following official url from IBM.
http://publib.boulder.ibm.com/infocenter/eserver/v1r2/index.jsp?topic=/diricinfo/fqm0_t_enabling_snmp_access_and_trap_forwarding_for_linux.html
In my system, snmp and snmplibs are... (1 Reply)
Discussion started by: SiddhV
1 Replies
10. IP Networking
Can someone help with a detail step-by-step oh how to configure DNS server on Linux Server.
-
I need to have 3 IP addresses map to a single hostname.
for clients
I'm a Linux rookie.
Thanks
Oscar (1 Reply)
Discussion started by: FrankOscar
1 Replies
HTABLE(8) System Manager's Manual HTABLE(8)
NAME
htable - convert NIC standard format host tables
SYNOPSIS
/etc/htable [ -c connected-nets ] [ -l local-nets ] file
DESCRIPTION
Htable is used to convert host files in the format specified in Internet RFC 810 to the format used by the network library routines. Three
files are created as a result of running htable: hosts, networks, and gateways. The hosts file may be used by the gethostbyname(3N) rou-
tines in mapping host names to addresses if the nameserver, named(8), is not used. The networks file is used by the getnetent(3N) routines
in mapping network names to numbers. The gateways file may be used by the routing daemon in identifying ``passive'' Internet gateways; see
routed(8C) for an explanation.
If any of the files localhosts, localnetworks, or localgateways are present in the current directory, the file's contents is prepended to
the output file. Of these, only the gateways file is interpreted. This allows sites to maintain local aliases and entries which are not
normally present in the master database. Only one gateway to each network will be placed in the gateways file; a gateway listed in the
localgateways file will override any in the input file.
If the gateways file is to be used, a list of networks to which the host is directly connected is specified with the -c flag. The net-
works, separated by commas, may be given by name or in Internet-standard dot notation, e.g. -c arpanet,128.32,local-ether-net. Htable
only includes gateways which are directly connected to one of the networks specified, or which can be reached from another gateway on a
connected net.
If the -l option is given with a list of networks (in the same format as for -c), these networks will be treated as ``local,'' and informa-
tion about hosts on local networks is taken only from the localhosts file. Entries for local hosts from the main database will be omitted.
This allows the localhosts file to completely override any entries in the input file.
Htable is best used in conjunction with the gettable(8C) program which retrieves the NIC database from a host.
SEE ALSO
intro(3N), gettable(8C), named(8)
BUGS
If the name-domain system provided network name mapping well as host name mapping, htable would no longer be needed.
4.2 Berkeley Distribution May 22, 1986 HTABLE(8)