Sponsored Content
Full Discussion: HP-UX Disk crash?
Special Forums Hardware Filesystems, Disks and Memory HP-UX Disk crash? Post 302134500 by Perderabo on Friday 31st of August 2007 07:35:26 AM
Old 08-31-2007
This command:
dd if=/dev/rdsk/c5t6d0 bs=4096 of=/dev/null
tries to read the entire disk and copy it to /dev/null. It may do nothing for the broken disk. But if it works, it usually causes some activity indication such as the green light flashing. You should draw a little picture of your JBOD cabinet and run the command for each disk to map them out. If you ID all of the good disks, the one that is left must be the bad disk. Once you ID a disk, use your interrupt character, usually cntl-c to kill the dd.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Disk Crash

We have a Unix system with two hard drives. When we tried to access it this morning it had frozen, and when we rebooted it couldn't find one of the hard drives, and had quite a few bad data blocks on the other. Of course we fear the worst: that the drive is completely gone, but were not sure how... (1 Reply)
Discussion started by: Kgatliffe
1 Replies

2. Filesystems, Disks and Memory

System crash and Disk erasure !!!

I need some expert help, and would appreciate any feedback on the following problem: After power outage the machine didn't allow the login. When we checked it , it looked like both disks were completely empty. Luckily, we have a backup machine, and we can restore the disks. Has anybody seen... (3 Replies)
Discussion started by: DGoubine
3 Replies

3. HP-UX

HP-UX system crash help please!!!

Hi, First of all, thanks for your help. I have downloaded freeBSD to study unix I'm here again 'cause my HP-UX 10.x has "broken". It raise this error: ---------------------------------------------------- Diagnostic System warning: = 0x1f005000 is POWERFAILED The diagnostic logging... (1 Reply)
Discussion started by: efrenba
1 Replies

4. Solaris

crash of my machine

I installed solaris 5.9 on a machine SunBlade100 512Mo of RAM and 18Go of hard disc, after the installation I have remark that the machine starts again after 10mn with 15 mn of walk, I downloaded and installed the last patchs on the machine but the poblème persists. someone can help me and tell me... (0 Replies)
Discussion started by: toufik
0 Replies

5. Solaris

crash dump

Can anyone of you help me in enabling crash dump on Solaris 5.5.1 (1 Reply)
Discussion started by: csreenivas
1 Replies

6. Solaris

crash dump

hi , i have machine that is crashed how i can enable core dump file & how can i find it ? :confused: (4 Replies)
Discussion started by: lid-j-one
4 Replies

7. Solaris

scconf crash: registering a Veritas local disk on Sun Cluster (localonly=true)

Hi all, I want to put a local disk on a Sun Cluster node but scconf command explodes :eek: My system: * two node cluster on two VMWare virtual machines * Solaris 10 SunOS 5.10 Generic_141415-05 i86pc i386 i86pc * Sun Cluster 3.2 u2 * Veritas Volume manager The situation... (2 Replies)
Discussion started by: gxmsgx
2 Replies

8. Solaris

crash dumps

I am supporting a server running Solaris 4.3.The server is not having ddicated system administrator and i am requred to do minor maintenance tasks.l From few days, The server is automatically crashing and i just reboot the server. I also do not see anything in /var/adm/messages that can give an... (1 Reply)
Discussion started by: asalman.qazi
1 Replies

9. SCO

Unixware Crash ...

Hi, I need help, one of our servers is down, and all data in that Server are critical: The Scenario: ------------- I have a computer with the next architecture: architecture=IA32 bus_types=PCI2.10,ISA,PnP1.0 hostname=xxx.xxx.xxx (the real name is hidden) hw_provider=Generic AT... (2 Replies)
Discussion started by: danilosevilla
2 Replies

10. Solaris

Boot disk crash with metadb config info

Hello all; We have a SunFire V240 with three disks that were part of a metadb. One of those disks, the boot disk, experienced a horrible death Monday night and we're now trying to recover from that. I know very little about metadb stuff, so please be gentle with me... I'm assuming... (3 Replies)
Discussion started by: Handon
3 Replies
cmdk(7D)							      Devices								  cmdk(7D)

NAME
cmdk - common disk driver SYNOPSIS
cmdk@target, lun : [ partition | slice ] DESCRIPTION
The cmdk device driver is a common interface to various disk devices. The driver supports magnetic fixed disks and magnetic removable disks. The block-files access the disk using the system's normal buffering mechanism and are read and written without regard to physical disk records. There is also a "raw" interface that provides for direct transmission between the disk and the user's read or write buffer. A sin- gle read or write call usually results in one I/O operation; raw I/O is therefore considerably more efficient when many bytes are transmit- ted. The names of the block files are found in /dev/dsk; the names of the raw files are found in /dev/rdsk. I/O requests to the magnetic disk must have an offset and transfer length that is a multiple of 512 bytes or the driver returns an EINVAL error. Slice 0 is normally used for the root file system on a disk, slice 1 as a paging area (for example, swap), and slice 2 for backing up the entire fdisk partition for Solaris software. Other slices may be used for usr file systems or system reserved area. Fdisk partition 0 is to access the entire disk and is generally used by the fdisk(1M) program. FILES
/dev/dsk/cndn[s|p]n block device (IDE) /dev/rdsk/cndn[s|p]n raw device (IDE) where: cn controller n dn lun n (0-7) sn UNIX system slice n (0-15) pn fdisk partition(0) /kernel/drv/cmdk 32-bit kernel module. /kernel/drv/amd64/cmdk 64-bit kernel module. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Architecture |x86 | +-----------------------------+-----------------------------+ SEE ALSO
fdisk(1M), mount(1M), lseek(2), read(2), write(2), readdir(3C), scsi(4), vfstab(4), attributes(5), dkio(7I) SunOS 5.10 9 Oct 2004 cmdk(7D)
All times are GMT -4. The time now is 06:13 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy