|
|
Sponsored Content
Operating Systems
Solaris
Solaris 10 install doesn't display Network Connectivity prompt page
Post 302134299 by sarahsi on Thursday 30th of August 2007 08:44:59 AM
08-30-2007
|
|
10 More Discussions You Might Find Interesting
1. IP Networking
Hi,
I would like to know how i can setup my unix computer to connect to novell. Anybody any idea? (5 Replies)
Discussion started by: edw1ns
5 Replies
2. UNIX for Dummies Questions & Answers
I want to reinstall a network printer (lexmark) on a solaris 8.
I had that working but now I have a Windos message "no printer installed"
I am a newbie... and hve no idea how to handle this situation.
Thanks
jose (2 Replies)
Discussion started by: reda
2 Replies
3. UNIX and Linux Applications
Hi All,
I need a basic overview of connecting a HTML web page to Unix
I will give a brief of my exact requirement.
There will be a front end HTML page - a web page which will have certain buttons.
Each button will have certain functionality.
For eg: There is a button for Disk Usage. When the... (1 Reply)
Discussion started by: abhilashnair
1 Replies
4. Solaris
Hi to all!
I want to learn step by step easily how to configure my Solaris for network. I know alot about Solaris Network configuration. But I have some problems.
When I install Solaris, and I plug-in my network cable to Solaris. Then I run:
ifconfig -a plumb
then I do
ifconfig bge0 dhcp... (7 Replies)
Discussion started by: SecureXCode
7 Replies
5. Solaris
hi,
i just completed installing O/S 5.9 on Sunfire 280R with O/S 5.9. During installation, i wasn't able to add IP, Default gateway, NDS and netmask because the lan port wasn't not active yet. Now that i have a lan port active, how to add network components onto the system?
I did ifconfig to... (1 Reply)
Discussion started by: lamoul
1 Replies
6. Solaris
Hi all,
I got a Fujitsu P650 server running on Solaris 9 and we are going to re-install Solaris 10 . W have a build server in a different IP segment. So we setup a boot server and /etc/ethers and /etc/bootparams are all updated. When I issue
boot net -install,
I'm getting the following... (3 Replies)
Discussion started by: mohzub
3 Replies
7. Solaris
Hi
i have created a solaris zone but have not yet connected any network cables for this new zone,
can i set the zone up without running the command 'add net' and not adding an ip or physical interface?
i tried to add dummy internet settings and get this
zonecfg:coddr> add net... (4 Replies)
Discussion started by: newbiesolaris10
4 Replies
8. UNIX for Dummies Questions & Answers
Good afternoon,
I wonder how i could use unix commands to ease the reading of long command result output ?
like the "php -i" or any other command that returns a long answer.
I could not find the right terms to Google it or search the forum. Therefore I bother you with this question.
... (3 Replies)
Discussion started by: Mat_k
3 Replies
9. HP-UX
Newbie with UNIX here.
Currently troubleshooting a UNIX terminal we have.
I determined it to be bad and swapped it out with a known good terminal. I went in and changed the IP address and host name to reflect the old terminal. Although now there is no connectivity.
I swapped out the NIC... (1 Reply)
Discussion started by: kevinlord190
1 Replies
10. Solaris
Hello all, thanks for reading my question:
So I've been a Unix/Linux SysAdmin for a couple years, and I'm a bit over my head running solo, trying to set up LDoms using Oracle VM Server 3.1 for SPARC. I've been very careful, and things have gone well up until the point I try to access the new... (9 Replies)
Discussion started by: Lyxix
9 Replies
LEARN ABOUT SUSE
install-solaris
install-solaris(1M) install-solaris(1M) NAME
install-solaris - install the Solaris operating system SYNOPSIS
install-solaris install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation, install-solaris invokes either a text-based installer or a graphical installer. The following minimum requirements for physical memory dictate which features are available during installation: For SPARC machines: 128 MB Minimum physical memory for all installation types 128 MB Minimum physical memory required for windowing system 384 MB Minimum physical memory required for graphical-based installation For x86 machines: 256 MB Minimum physical memory for all installation types 256 MB Minimum physical memory required for windowing system 512 MB Minimum physical memory required for graphical-based installation In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea- tures available. install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more details. install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the installation media. Refer to the for disk space requirements. Refer to the for more information on the various menus and selections. See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcdrom (Solaris instal- | | |lation media) | +-----------------------------+-----------------------------+ |Interface Stability |Evolving | +-----------------------------+-----------------------------+ pkginfo(1), install(1M), pkgadd(1M), attributes(5) It is advisable to exit install-solaris by means of the exit options in the install-solaris menus. 23 Sep 2005 install-solaris(1M)