Sponsored Content
Full Discussion: Ultra 60 won't boot
Operating Systems Solaris Ultra 60 won't boot Post 302133756 by zosojohnny on Saturday 25th of August 2007 08:07:29 AM
Old 08-25-2007
Ultra 60 won't boot

I just was given an Ultra 60 that I'm trying to get started so that I can re-load the system with Solaris 10. I can't seem to get the system to boot past the initial memory check. I've tried to do an Stop-A to get to the eeprom, but can't do that. My next step is to try to send a break from the serial port.

Here is what I get when I boot:

Sun Ultra 60 UPA/PCI (UltraSPARC-II 360 MHZ), Keyboard Present
OpenBoot 3.23, 256 MB memory installed, Serial #10577431.
Ethernet address 8:0:20:a1:66:17, Host ID: 80a16617

Then it does the little whirly thing counting the memory and I get a block cursor.

thats it....can anyone help me...

thanks
 

10 More Discussions You Might Find Interesting

1. Solaris

Solaris (9) won't boot!

Hi, I've just bought an Ultra 60 running solaris 9 (or so I've been led to believe). When I start up, it looks for a (presumably) domain/network to hook up to and the following messages are displayed: Boot device: net file and args: Network link setup failed Please check cable and try... (3 Replies)
Discussion started by: alarmcall
3 Replies

2. Solaris

cannot find boot device and won't boot off cdrom

I'm running solaris 2.5.1. My main development server is DEAD, i can't even boot off the cdrom, it powers up, acts like it is starting the boot process but then says cannot find boot device. I've done the search here on this site and saw the other posts, but at the ok prompt it won't even let me... (3 Replies)
Discussion started by: kymberm
3 Replies

3. AIX

won't mount /usr...won't boot fully

Hello: NOOB here. I attempted to use smit mkcd. Failed on first attempt, not enough space. 2nd attempt tried to place iso on /usr, not enough space there. Cleanup ran for about 5 minutes after aborting. Now AIX won't boot. LCD display on 7029-6E3 says: 0517 MOUNT /USR. Attempted to boot from CD... (11 Replies)
Discussion started by: bbird
11 Replies

4. Solaris

Sun Sparc Ultra 4 won't boot - disk errors

Hi all. I am seeing in one of our less-used servers that it crashed and now won't restart. I get the message 'continue with normal startup or boot into maintenance mode'. I go into maintenance and run fsck on /usr0 (mentioned in error at restart) it then reboots but goes right back to... (3 Replies)
Discussion started by: jamie_collins
3 Replies

5. UNIX for Dummies Questions & Answers

SUN Ultra 10 won't boot - Help Please

Folks; My SUN Ultra 10 5.9 won't boot. It only stops after counting the memory on the white screen then hangs there with nothing. even the power button won't take it down from there, i had to unplug it then re-plug it again. i inserted a disk with Solaris 9 iso trying to rebuild it but nothing... (1 Reply)
Discussion started by: Katkota
1 Replies

6. Solaris

Ultra 5 will not boot from DVD ROM :(

Hi, I just got a new Ultra 5 and replaced the CD-ROM with an LG DVD-ROM (approved and listed in Sun HCL). Got the DVD-ROM installed to install Solaris 10. Im just learning and new to Solaris installation. When I insert a Solaris 10 DVD I see that it gets mounted and File Manager opens and... (8 Replies)
Discussion started by: greypilgrim
8 Replies

7. UNIX for Dummies Questions & Answers

New kernel won't boot

I compiled new kernel in linux 10.04 called linux-2.6.26.8-xenomai, it runs alongside the other kernel, but when I want to boot it I get an error message saying: Missing modules (cat /proc/modules; ls /dev) ALERT! /dev/sda5 does not exist. After making the modules and headers I made the... (4 Replies)
Discussion started by: mdop
4 Replies

8. Solaris

Ultra 45 Boot Loop

I am trying to get an old Ultra 45 to boot and it is stuck in a loop. I cannot get anything to come up on a monitor, so when I hook up a serial connection to the TTYa interface I see the following output: @(#)OBP 4.21.2 2005/12/22 17:17 Sun Ultra 45 Workstation Clearing TLBs Loading... (0 Replies)
Discussion started by: Madrox72
0 Replies

9. UNIX for Beginners Questions & Answers

Sun ultra 30 boot problem

Hi all, I've got a Sun ultra 30 workstation. the Nvram battery died so I replaced it. I reprogrammed the mac address using the mlpl command all that so it booted without error. But for some reason I was trying to boot via the network. So I did a STOP A and boot disk1 which is the alias for my SCSI... (2 Replies)
Discussion started by: robbo007
2 Replies

10. Solaris

Sun Ultra 30 boot problems

Hi all, I've just replaced the eprom battery on my Sun Ultra-30 and having boot issues. For some reason its trying to boot off the network instead of the DISK1. Howe can I change it so the open boot does not default to the boot device: NET Thanks, Rob (3 Replies)
Discussion started by: robbo007
3 Replies
HME(4)							   BSD Kernel Interfaces Manual 						    HME(4)

NAME
hme -- Sun Microelectronics STP2002-STQ Ethernet interfaces device driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device miibus device hme Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_hme_load="YES" DESCRIPTION
The hme driver supports Sun Microelectronics STP2002-STQ ``Happy Meal Ethernet'' Fast Ethernet interfaces. All controllers supported by the hme driver have TCP checksum offload capability for both receive and transmit, support for the reception and transmission of extended frames for vlan(4) and a 128-bit multicast hash filter. HARDWARE
The hme driver supports the on-board Ethernet interfaces of many Sun UltraSPARC workstation and server models. Cards supported by the hme driver include: o Sun PCI SunSwift Adapter (``SUNW,hme'') o Sun SBus SunSwift Adapter (``hme'' and ``SUNW,hme'') o Sun PCI Sun100BaseT Adapter 2.0 (``SUNW,hme'') o Sun SBus Sun100BaseT 2.0 (``SUNW,hme'') o Sun PCI Quad FastEthernet Controller (``SUNW,qfe'') o Sun SBus Quad FastEthernet Controller (``SUNW,qfe'') NOTES
On sparc64 the hme driver respects the local-mac-address? system configuration variable which can be set in the Open Firmware boot monitor using the setenv command or by eeprom(8). If set to ``false'' (the default), the hme driver will use the system's default MAC address for all of its devices. If set to ``true'', the unique MAC address of each interface is used if present rather than the system's default MAC address. Supported interfaces having their own MAC address include on-board versions on boards equipped with more than one Ethernet interface and all add-on cards except the single-port SBus versions. SEE ALSO
altq(4), intro(4), miibus(4), netintro(4), vlan(4), eeprom(8), ifconfig(8) Sun Microelectronics, STP2002QFP Fast Ethernet, Parallel Port, SCSI (FEPS) User's Guide, April 1996, http://mediacast.sun.com/users/Barton808/media/STP2002QFP-FEPs_UG.pdf. HISTORY
The hme driver first appeared in NetBSD 1.5. The first FreeBSD version to include it was FreeBSD 5.0. AUTHORS
The hme driver was written by Paul Kranenburg <pk@NetBSD.org>. BSD
June 14, 2009 BSD
All times are GMT -4. The time now is 11:31 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy