08-23-2007
robotronic thanks ...
Thanks for robotronic 's help.
but i was mistake the result i obtain from the router must be look like this
"Router#ping 192.168.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 104/104/104 ms
Router#"
there must be 7 lines how can i get the middle average value
in addition, how i can handle the non standard reply , (e.g the remote cannot be ping)
Router#ping 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
U.U..
Success rate is 0 percent (0/5)
Router#
anyway, thanks for robotronic 's help as I had already search for a very long time for nothing.
Last edited by optimus; 08-23-2007 at 03:59 PM..
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi All,
I am connected to a cisco router and I want to know the hostname of this router.
I connect as telnet <IPADDRESS>
and the prompt shows
vpnaccess-bristol>
But I want to know the full hostname of the router how can i do that.
When i type the hostname command the following... (3 Replies)
Discussion started by: rahulrathod
3 Replies
2. IP Networking
Dear All,
I have worked with xDSL routers working in bridged mode, and linux behind them working as a Firewall utilizing IPTABLES. My question is, how this will change if the xDSL router is replaced with a Cisco Router?
I mean to ask that, can I assign a public ip on the linux machine, which... (0 Replies)
Discussion started by: tmm
0 Replies
3. IP Networking
Hello all,
I have set up dhcpd on a linux box for serving subnets on multiple vlans configured on a Cisco 6500 with ip helper of the dhcp server. Servers get dhcp leases just fine, however, some machines lose their connection for reboot or what not and I can not get their lease back even though... (0 Replies)
Discussion started by: closedown
0 Replies
4. Shell Programming and Scripting
Hi Experts,
I am using perl to telnet on cisco boxes. We have this stupid cisco node which does not support "terminal Length0" command.
Since I am using Net::Telnet and capturing output with
@output = $telnet->cmd('cmd');
Say
@output = $telnet->cmd('show version');
Now problem... (2 Replies)
Discussion started by: mtomar
2 Replies
5. Shell Programming and Scripting
I am writing perl script to configure Cisco device but Variables inside Net::Telnet::Cisco Module doesn't work and passed to device without resolving.
Please advise.
here is a sample of script:
use Net::Telnet::Cisco;
$device = "10.14.199.1";
($o1, $o2, $o3, $o4) = split(/\./,$device);... (5 Replies)
Discussion started by: ahmed_zaher
5 Replies
6. Shell Programming and Scripting
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
Discussion started by: gokcell
1 Replies
7. Shell Programming and Scripting
Hi all
i have little problem finding solution about simple telnet script .... i have 250 routers and on some i have different password and on some they ask just for password no username. So for example 1,2,3 have username and password (user,password) 4, and 5 have different username and password... (0 Replies)
Discussion started by: IvanMP
0 Replies
8. Shell Programming and Scripting
I have a perl script that is called with a router name command list file and output file. The command file can be very large, up to 3k of commands. At first I dumped the command list file to an array and ran the entire file on the router and captured the output. It worked ok for a command list in... (1 Reply)
Discussion started by: numele
1 Replies
9. IP Networking
I bought a Cisco 892-k9 router and I am having in issue trying to setup the initial configuration. Does someone have a sampl configuration for a single subnet that I can use for my configuration?
Thanks. (0 Replies)
Discussion started by: gandolf989
0 Replies
LEARN ABOUT DEBIAN
hobbitping
HOBBITPING(1) General Commands Manual HOBBITPING(1)
NAME
hobbitping - Xymon ping tool
SYNOPSIS
hobbitping [--retries=N] [--timeout=N] [IP-adresses]
DESCRIPTION
hobbitping(1) is used for ping testing of the hosts monitored by the xymon(7) monitoring system. It reads a list of IP adresses from stdin,
and performs a "ping" check to see if these hosts are alive. It is normally invoked by the bbtest-net(1) utility, which performs all of
the Xymon network tests.
Optionally, if a list of IP-adresses is passed as commandline arguments, it will ping those IP's instead of reading them from stdin.
hobbitping only handles IP-adresses, not hostnames.
hobbitping was inspired by the fping(1) tool, but has been written from scratch to implement a fast ping tester without much of the over-
head found in other such utilities. The output from hobbitping is similar to that of "fping -Ae".
hobbitping probes multiple systems in parallel, and the runtime is therefore mostly dependant on the timeout-setting and the number of
retries. With the default options, hobbitping takes approximately 18 seconds to ping all hosts (tested with an input set of 1500 IP
adresses).
SUID-ROOT INSTALLATION REQUIRED
hobbitping needs to be installed with suid-root privileges, since it requires a "raw socket" to send and receive ICMP Echo (ping) packets.
hobbitping is implemented such that it immediately drops the root privileges, and only regains them to perform two operations: Obtaining
the raw socket, and optionally binding it to a specific source address. These operations are performed as root, the rest of the time hob-
bitping runs with normal user privileges. Specifically, no user-supplied data or network data is used while running with root privileges.
Therefore it should be safe to provide hobbitping with the necessary suid-root privileges.
OPTIONS
--retries=N
Sets the number of retries for hosts that fail to respond to the initial ping, i.e. the number of ping probes sent in addition to
the initial probe. The default is --retries=2, to ping a host 3 times before concluding that it is not responding.
--timeout=N
Determines the timeout (in seconds) for ping probes. If a host does not respond within N seconds, it is regarded as unavailable,
unless it responds to one of the retries. The default is --timeout=5.
--responses=N
hobbitping normally stops pinging a host after receiving a single response, and uses that to determine the round-trip time. If the
first response takes longer to arrive - e.g. because of additional network overhead when first determining the route to the target
host - it may skew the round-trip-time reports. You can then use this option to require N responses, and hobbitping will calculate
the round-trip time as the average of all of responsetimes.
--max-pps=N
Maximum number of packets per second. This limits the number of ICMP packets hobbitping will send per second, by enforcing a brief
delay after each packet is sent. The default setting is to send a maximum of 50 packets per second. Note that increasing this may
cause flooding of the network, and since ICMP packets can be discarded by routers and other network equipment, this can cause
erratic behaviour with hosts recorded as not responding when they are in fact OK.
--source=ADDRESS
Use ADDRESS as the source IP address of the ping packets sent. On multi-homed systems, allows you to select the source IP of the
hosts going out, which might be necessary for ping to work.
--debug
Enable debug output. This prints out all packets sent and received.
SEE ALSO
xymon(7), bbtest-net(1), fping(1)
Xymon Version 4.2.3: 4 Feb 2009 HOBBITPING(1)