08-16-2007
Your routing table is incorrect. You have not set up the table properly. Please review and get back to me with what you think might be wrong. Thanks.
10 More Discussions You Might Find Interesting
1. AIX
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
2. IP Networking
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies
3. HP-UX
Hi,
My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13
I tried with:
#route add 192.168.80.2 255.255.255.255 10.10.10.13
but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable
I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies
4. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
5. IP Networking
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies
6. Solaris
Hey Guys:
I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1
add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies
7. Solaris
Hi need to add 2 routes, one on each server.
I know the route add comand but I have always been given the parameters to put in.
I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ?
In... (6 Replies)
Discussion started by: vettec3
6 Replies
8. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
9. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
10. IP Networking
Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254
if not working, please try gateway through management port: 10.128.55.254
Just want to double confirm if this would be the correct command
#route add -net 10.128.255.41/32 10.128.201.254
And if didnt work
#route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
LEARN ABOUT DEBIAN
secvpn
SECVPN(1) General Commands Manual SECVPN(1)
NAME
secvpn - Control the Secure Virtual Private Network
SYNOPSIS
secvpn [-v][-n][-s][-r] start|stop|routedel|routeadd|test|status [Host]
DESCRIPTION
Secvpn builds a virtual private network (vpn) as defined in /etc/network/secvpn.conf. The vpn uses encryption based on ssh security.
Before secvpn can be used you have to create some prerequisites. See PREREQUISITES below.
The following subcommands may be used with secvpn:
start is used to start the vpn. Secvpn will add new ppp interfaces necessary to make the vpn work, but will not automatically add routes
(see the routeadd option below). If the recursive option is set, secvpn will log into the passive hosts and run "secvpn -r start" on
them too.
stop is used to stop the vpn.
routeadd
is used to setup new routing entries based on secvpn.conf. Secvpn will first add the route active->passive, then tell the passive
host to add the route back. The route in the passive host will be added according to the configuration file there (in the passive
host), so if the configuration files differ, things will not work.
routedel
will delete the routing entries built with routeadd.
test checks whether the ppp interface is used to reach O_CRYPT_IP.
status same as test, but checks all vpns if no host is named (instead of only active vpns as 'test' does).
OPTIONS
-v verbose output
-n do nothing
-s be silent
-r work recursive
PREREQUISITES
Before secvpn can be used you have to enable passwordless ssh access for user "secvpn" from the initiator secvpn pc to the target secvpn
pc. Use authorized_ keys or RhostsRSAAuthentication with the .shosts file. Have a look to the ssh - manpages for more information.
Before secvpn can be used you have to give root rights for specific commands to the user "secvpn". This can be done with the followin com-
mand:
echo "secvpn ALL=NOPASSWD: /usr/sbin/secvpn, /usr/sbin/pppd" >>/etc/sudoers
Before secvpn can be used you have to edit /etc/secvon.conf. See secvpn.conf(4).
EXAMPLES
There are 3 examples in /usr/share/doc/secvpn/examples:
Example1: secvpn acts as router connection 2 subnets
Example2: secvpn having one lan-card and connect 2 subnets
Example3: secvpn having one lan-card and connect 11 subnets in a tree structure
OTHER
To have real security it is necessary to secure each secvpn host and to have firewalls on each secvpn host allowing only selected IP-
Adresses and Ports to pass through the VPN.
AUTHOR
Bernd Schumacher, HP Consulting, HEWLETT-PACKARD GmbH, Bad Homburg, 2000-2005
COPYRIGHT
Copyright: Most recent version of the GPL.
On Debian GNU/Linux systems, the complete text of the GNU General Public License can be found in "/usr/share/common-licenses/GPL".
SEE ALSO
secvpn(1) secvpnmon(1) ssh(1) timeout(1) secvpn.conf(4)
secvpn August 2000 SECVPN(1)