08-16-2007
Your routing table is incorrect. You have not set up the table properly. Please review and get back to me with what you think might be wrong. Thanks.
10 More Discussions You Might Find Interesting
1. AIX
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
2. IP Networking
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies
3. HP-UX
Hi,
My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13
I tried with:
#route add 192.168.80.2 255.255.255.255 10.10.10.13
but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable
I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies
4. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
5. IP Networking
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies
6. Solaris
Hey Guys:
I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1
add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies
7. Solaris
Hi need to add 2 routes, one on each server.
I know the route add comand but I have always been given the parameters to put in.
I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ?
In... (6 Replies)
Discussion started by: vettec3
6 Replies
8. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
9. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
10. IP Networking
Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254
if not working, please try gateway through management port: 10.128.55.254
Just want to double confirm if this would be the correct command
#route add -net 10.128.255.41/32 10.128.201.254
And if didnt work
#route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
LEARN ABOUT DEBIAN
anytun-showtables
ANYTUN-SHOWTABLES(8) ANYTUN-SHOWTABLES(8)
NAME
anytun-showtables - anycast tunneling routing table visualization utility
SYNOPSIS
anytun-showtables
DESCRIPTION
anytun-showtables displays routing and connection tables used by Anytun. It can be used to display a saved routing/connection table used by
anytun-controld or to connect to a the sync port of Anytun.
OPTIONS
This Tool does not take any options. It takes the sync information from the standard input and prints the routing table to the standard
output.
EXAMPLES
Print routing table stored in local file
# perl -ne 'chomp; print' < routingtable | ./anytun-showtables
Print current routing table and watch changes
# nc unicast1.anycast.anytun.org 23 | ./anytun-showtables
BUGS
Most likely there are some bugs in Anytun. If you find a bug, please let the developers know at satp@anytun.org. Of course, patches are
preferred.
SEE ALSO
anytun(8), anytun-controld(8), anytun-config(8)
AUTHORS
Othmar Gsenger <otti@anytun.org> Erwin Nindl <nine@anytun.org> Christian Pointner <equinox@anytun.org>
RESOURCES
Main web site: http://www.anytun.org/
COPYING
Copyright (C) 2007-2009 Othmar Gsenger, Erwin Nindl and Christian Pointner. This program is free software: you can redistribute it and/or
modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License,
or any later version.
12/30/2011 ANYTUN-SHOWTABLES(8)