08-06-2007
Thanks Awadhesh, i got the information from link you specified
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
From a PROM ok prompt I have typed banner. This returned this info
SunSPARCStation20 (1X390Z50) ......
Okay, I read that the 1x390z50 is the processor type. How can I found out the speed of these processor? Is it 50mhz? Don't know but I am curious. Thanks (5 Replies)
Discussion started by: jwbrown
5 Replies
2. Shell Programming and Scripting
Hi Everyone
I am new to unix. I ahve few quries that i would like to post.
Is there any way by which i get the unique processor Id. Actually i am unable to find any logic and method to get access to Processor Id.
Is it possible to get it. I read it on Intel site that the new processor do no... (1 Reply)
Discussion started by: atul.saxena
1 Replies
3. AIX
Question is on setting of Physical and Virtual processors for LPARs to make proper use of virtualization capabilities.
Environment is a 8-way p570 with 4 LPARs.
lparVIO1 and lparVIO2:
AIX 5300-04-01
Mode/Type= Shared-SMT/Capped
Minimum Processors= 0.10
Desired Processors= 0.50
Maximum... (1 Reply)
Discussion started by: guttew
1 Replies
4. UNIX for Dummies Questions & Answers
Hi All,
What is the command to identify whether a processor is single core / dual core in solaris ?
Thanks. (2 Replies)
Discussion started by: RAA
2 Replies
5. AIX
Guys...
Hows it going???
I have been going through the hardware spec of IBM system p systems.. and here i am confused
for IBM Power 520 Express it says
Processor cores:
One, two or four 64-bit 4.2 GHz POWER6 with AltiVec™ SIMD and Hardware Decimal Floating-Point acceleration
... (1 Reply)
Discussion started by: balaji_prk
1 Replies
6. UNIX for Dummies Questions & Answers
How to find out whether the system has multiple processors.
In multiprocessor system how to get their names or ids
How to send command to a particular processor ( can we use rsh) (6 Replies)
Discussion started by: anjum
6 Replies
7. Shell Programming and Scripting
Hi
I need a command to know how many processors are available and what is their speed in UNIX.
Thanks (2 Replies)
Discussion started by: diksha2207
2 Replies
8. AIX
Processor failed on POWER 5 machine, i have other "test" machine with different machine type, can i recover the production machine by moving its disks and HBAs to the other test machine ?? (4 Replies)
Discussion started by: majd_ece
4 Replies
9. Shell Programming and Scripting
hi,
what plugins i need to install to run m4 processor in bash shell. Also, what is the file extension for m4 processor ( like .cc in c ).
Thanks (1 Reply)
Discussion started by: Learnerabc
1 Replies
10. UNIX for Dummies Questions & Answers
hello Admins,
how to find number of processor in unix machine. (2 Replies)
Discussion started by: vipinkumarr89
2 Replies
link(1) General Commands Manual link(1)
NAME
link, unlink - Creates an additional directory entry for an existing file
SYNOPSIS
link file1 file2
unlink file
STANDARDS
Interfaces documented on this reference page conform to industry standards as follows:
link: XCU5.0
unlink: XCU5.0
Refer to the standards(5) reference page for more information about industry standards and associated tags.
DESCRIPTION
The link command performs the link() system call to create an additional directory entry for an existing file, file1. In effect, the
underlying file then has two names, file1 and file2 (either of these arguments can be a pathname). The old and new entries share equal
access rights to the underlying file.
The unlink command performs the unlink() system call to remove a link to file created by link. The unlink command removes the directory
entry specified by the file parameter and, if the entry is a hard link, decrements the link count of the file referenced by the link.
You should be familiar with the link() and unlink() system calls before you use these commands.
The link and unlink commands do not issue error messages when the associated system call is unsuccessful.
NOTES
The link and unlink commands cannot be used to link and unlink directories.
EXIT STATUS
The link and unlink commands both exit with the following: The link() or unlink() system call succeeded. Too few or too many arguments
specified. The link() or unlink() system call failed.
SEE ALSO
Commands: fsck(8), ln(1)
Functions: link(2), unlink(2)
link(1)