Sponsored Content
Operating Systems SCO SCO OpenServer 5.0.7 Installation problem Post 302129895 by hafizurr on Thursday 2nd of August 2007 07:25:43 AM
Old 08-02-2007
Thanks its done,

Install without AD320 cotroller, unix boot oK.

Best Regards

Hafeez
 

10 More Discussions You Might Find Interesting

1. IP Networking

Installation Problem in Unix Openserver

I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies

2. Filesystems, Disks and Memory

SCO openserver 5 install problem

Hello all, I'm trying to install SCO openserver 5 on a 2.5 Gig hard drive, and I tried fdisk and a low-level format of the drive. When I insert the boot diskette all seems fine, and it asks me to set the cd-rom and it sees it and reads from it. Well, I'm thinking all is well until right after I... (1 Reply)
Discussion started by: immulett
1 Replies

3. UNIX for Dummies Questions & Answers

SCO OpenServer Booting Problem

My company has a Compaq NeoServer running SCO OpenServer Release 5 (vintage late 1998) that we inherited from another small company. This has been a very reliable file server for our small company. We recently installed a new Linux server and would like to convert the NeoServer to other functions... (1 Reply)
Discussion started by: Jeff Boyce
1 Replies

4. UNIX for Dummies Questions & Answers

RE: login problem with SCO openserver

I am running the beta version of Openserver by SCO and the Graphical login only gives me the option of logging into the system v xwindows and I know that this build included KDE 3.3 I have tried the kde kdm command at shell prompt: command not found. Any ideas anyone? (0 Replies)
Discussion started by: coreykirk
0 Replies

5. SCO

sco openserver 5.07 installation problem

Hi everyone, We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies

6. SCO

SCO OpenServer 5.0.7 Installation problem on HP ML310 G4

can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue tried hpsas aacraid lsil a160 a320 server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies

7. SCO

sco openserver release 5.0.5 installation problems on notebook

hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies

8. SCO

SCO OpenServer 5.0.5 Problem

I am currently having a problem with my SCO OpenServer 5.0.5 / 3.2v5.0.5 system. Running smoothly for the past 3 years, at random on March 16, 2010 the system crashes. I reboot it. Everything is normal again. 9 hours later it crashes again. This cycle has repeated itself ever since then. System... (2 Replies)
Discussion started by: jesmith
2 Replies

9. UNIX for Advanced & Expert Users

Installation of Sco Openserver 5.0.7 on HP DC 7600

Hi All , I wanted to install SCO Open server 5.0.7 on HP DC7600 Desktop Machine, is there any bootloader and which site i can find it to enable me install it because the system is not recognizing the Hard disk just like the ML G Series machine installations. Please help if you have done this... (4 Replies)
Discussion started by: davosky
4 Replies

10. SCO

Installation on SCO Openserver 5.0.5

Hello all, First off- great forum! I have learned a lot just by reading some of the questions and answers. Good to see there are good people out there still willing to help! Here is my dilemma- I have a fairly new server running an Activant product on it, which runs SCO openserver 5.0.5... (9 Replies)
Discussion started by: crt001
9 Replies
TWS(4)							   BSD Kernel Interfaces Manual 						    TWS(4)

NAME
tws -- 3ware 9750 SATA+SAS 6Gb/s RAID controller card driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device scbus device tws Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): tws_load="YES" DESCRIPTION
The tws driver provides support for LSI's 3ware 9750 SATA+SAS 6Gb/s RAID controller cards. These controllers feature the LSISAS2108 6Gb/s SAS RAID-on-Chip (ROC) and are available in 4- and 8-port configurations, supports RAID levels 0, 1, 5, 6, 10, 50 and single disk, with 96 SATA and/or SAS hard drives and SSDs. For further hardware information, see http://www.lsi.com/. HARDWARE
The tws driver supports the following SATA/SAS RAID controller: o LSI's 3ware SAS 9750 series LOADER TUNABLES
Tunables can be set at the loader(8) prompt before booting the kernel or stored in loader.conf(5). hw.tws.cam_depth The maximum queued CAM SIM requests for one controller. The default value is 256. hw.tws.enable_msi This tunable enables MSI support on the controller if set to a non-zero value. The default value is 0. hw.tws.queue_depth The maximum queued requests for one controller. hw.tws.use_32bit_sgls Limit the driver to use only 32-bit SG elements regardless whether the operating system is running in 64-bit mode. The default value is 0. FILES
/dev/da? array/logical disk interface /dev/tws? management interface DIAGNOSTICS
Whenever the driver encounters a command failure, it prints out an error code in the format: "ERROR: (<error source>: <error code>):", fol- lowed by a text description of the error. There are other error messages and warnings that the driver prints out, depending on the kinds of errors that it encounters. If the driver is compiled with TWS_DEBUG defined, it prints out a whole bunch of debug messages. SEE ALSO
da(4), scsi(4) AUTHORS
The tws driver was written by Manjunath Ranganathaiah for LSI and this manual page was written by Xin LI <delphij@FreeBSD.org> for iXsystems, Inc. BSD
October 4, 2011 BSD
All times are GMT -4. The time now is 11:35 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy