|
|
Sponsored Content
Operating Systems
SCO
SCO OpenServer 5.0.7 Installation problem on HP ML310 G4
Post 302129733 by wildginger on Wednesday 1st of August 2007 10:51:52 AM
08-01-2007
SCO OpenServer 5.0.7 Installation problem on HP ML310 G4
can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????
|
|
10 More Discussions You Might Find Interesting
1. IP Networking
I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies
2. Filesystems, Disks and Memory
Hello all,
I'm trying to install SCO openserver 5 on a 2.5 Gig hard drive, and I tried fdisk and a low-level format of the drive. When I insert the boot diskette all seems fine, and it asks me to set the cd-rom and it sees it and reads from it. Well, I'm thinking all is well until right after I... (1 Reply)
Discussion started by: immulett
1 Replies
3. UNIX for Dummies Questions & Answers
My company has a Compaq NeoServer running SCO OpenServer Release 5 (vintage late 1998) that we inherited from another small company. This has been a very reliable file server for our small company. We recently installed a new Linux server and would like to convert the NeoServer to other functions... (1 Reply)
Discussion started by: Jeff Boyce
1 Replies
4. UNIX for Dummies Questions & Answers
I am running the beta version of Openserver by SCO and the
Graphical login only gives me the option of logging into the
system v xwindows and I know that this build included KDE 3.3
I have tried the kde kdm command at shell prompt: command not
found. Any ideas anyone? (0 Replies)
Discussion started by: coreykirk
0 Replies
5. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
6. SCO
we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached).
At the time of installation we link both driver BTLD
Boot: Defbootstr link=accraid ad320
Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies
7. SCO
hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies
8. SCO
I am currently having a problem with my SCO OpenServer 5.0.5 / 3.2v5.0.5 system.
Running smoothly for the past 3 years, at random on March 16, 2010 the system crashes. I reboot it. Everything is normal again. 9 hours later it crashes again. This cycle has repeated itself ever since then. System... (2 Replies)
Discussion started by: jesmith
2 Replies
9. UNIX for Advanced & Expert Users
Hi All ,
I wanted to install SCO Open server 5.0.7 on HP DC7600 Desktop Machine, is there any bootloader and which site i can find it to enable me install it because the system is not recognizing the Hard disk just like the ML G Series machine installations.
Please help if you have done this... (4 Replies)
Discussion started by: davosky
4 Replies
10. SCO
Hello all,
First off- great forum! I have learned a lot just by reading some of the questions and answers. Good to see there are good people out there still willing to help!
Here is my dilemma- I have a fairly new server running an Activant product on it, which runs SCO openserver 5.0.5... (9 Replies)
Discussion started by: crt001
9 Replies
LEARN ABOUT DEBIAN
rmcp-ping
RMCPING(8) System Manager Commands RMCPING(8) NAME
rmcpping - send RMCP Ping to network hosts SYNOPSIS
rmcpping [OPTION...] destination DESCRIPTION
rmcpping uses the RMCP Ping request datagram to elicit an RMCP Pong response from a remote host. The utility can be used to verify if a remote host supports RMCP or IPMI. The initial starting sequence number will be randomized. rmcpping will return 0 to the environment if it receives atleast 1 response from the remote host. Otherwise, it exits with a value of 1. OPTIONS
The following options are available -h Output help menu. -V Output version. -c count Stop after sending count packets. -i interval Wait interval seconds between sending each packet. The default is to wait for one second between each packet. -I interface address Set source address to specified interface address. Argument may be numeric IP address or name of device. -t timeout Time to wait for a response, in seconds. Default is five seconds. -v Verbose output. -s num Specify an initial starting sequence number. The default is to use a random initial sequence number. -d Turn on debugging. KNOWN ISSUES
It has been observed that some remote BMCs can get "confused" and delay packet responses if duplicate packets (with duplicate sequence num- bers) are sent in succession very quickly. There is no known way to cleanly deal with a "confused" BMC other than the wait awhile. Unlike ping(8), local network devicess (e.g. 127.0.0.1) cannot be "pinged". REPORTING BUGS
Report bugs to <freeipmi-users@gnu.org> or <freeipmi-devel@gnu.org>. COPYRIGHT
Copyright (C) 2007-2012 Lawrence Livermore National Security, LLC. Copyright (C) 2003-2007 The Regents of the University of California. This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 3 of the License, or (at your option) any later version. ORIGIN
Command and manpage based off ping(8). SEE ALSO
freeipmi(7), ping(8), ipmiping(8) http://www.gnu.org/software/freeipmi/ rmcpping 1.1.5 2012-06-15 RMCPING(8)