07-24-2007
Thanks for your answer.
I have found that the boot was blocked by NFS.
All is OK now
regards
10 More Discussions You Might Find Interesting
1. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
2. AIX
I've got an RS6K B50, and i've installed AIX 5.3, TL5. It installs fine, the only customisations i make to the BOS are to change the locale / keyboard layout to UK, and to choose not to install graphical software.
I have no video card in this box, and i connect via a serial console (null modem... (4 Replies)
Discussion started by: craigp84
4 Replies
3. AIX
Hi guys,
Got a tiny bit of a problem on one of our servers here at work. I installed AIX 5.3 on the server and that went fine. Then I upgraded to ML 5300-05-01, but now the system just hangs on boot.
The system starts up and the monitor comes on in few minutes, but a few seconds later when... (6 Replies)
Discussion started by: drchris
6 Replies
4. AIX
To All:
I have this AIX machine (see boot process below). The problem was it hangs at:
The ctrmc Subsystem has been started. Subsystem PID is 11906..
I checked with other forums but their advise were just "strong punches in the air" with no specific explanation.
I really appreciate if... (6 Replies)
Discussion started by: aix_xia
6 Replies
5. Ubuntu
Boot process hangs after reaching the following line:
Adding 5853176k swap on /dev/mapper/mch-swap_1. Priority:-1 extents:1 across:5853176kUsing knoppix 6.2 as LiveCD, and mounting the partitions, I got the following:
# /etc/fstab: static file system information.
#
# Use 'blkid -o value -s... (0 Replies)
Discussion started by: fzaker
0 Replies
6. AIX
Hi all,
We have a old Power4 server with AIX version 5.3 installed. Upon boot up, it hangs right after the AIX welcome screen. On the diagnostic load progress LED indicator, I saw that it stopped at '0c32' then after awhile the LED would be blank. The screen on the monitor will hang at the black... (15 Replies)
Discussion started by: a_sim
15 Replies
7. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
8. Solaris
Got a strange problem.
I have 4 Solaris servers all configured the same, Solaris 10 x86 update 10.
When I try to ssh from one Solaris 10 server to another server ssh hangs.
I have an identical server and when I try this everything works fine.
The weird thing is if I am root on the server... (1 Reply)
Discussion started by: ccj4467
1 Replies
9. Solaris
Hi Guys,
I have a SunBlade 1500 which I use to practice at home. Suddenly when I power on the server it just displays the solaris banner and Boot device: disk File and args: Then it stops and says " rebooting with command: boot"
It doesn't boot to the kernel. Is there anyway I can possibly... (5 Replies)
Discussion started by: cjashu
5 Replies
10. Solaris
Power server up runs through diagnostics.
Goes to the boot section and then the bit where the cursor is spinning and thats it. Hangs completely.
Any ideas? (10 Replies)
Discussion started by: psychocandy
10 Replies
LEARN ABOUT MOJAVE
showmount
SHOWMOUNT(8) BSD System Manager's Manual SHOWMOUNT(8)
NAME
showmount -- show remote NFS mounts on host
SYNOPSIS
showmount [-Ae36] [-a | -d] [host]
DESCRIPTION
showmount shows status information about the NFS server on host. By default it prints the names of all hosts that have NFS file systems
mounted on the host. See NFS: Network File System Protocol Specification, RFC 1094, Appendix A, and NFS: Network File System Version 3
Protocol Specification, Appendix I, for a detailed description of the protocol.
-A Search for NFS servers advertised via Bonjour.
-a List all mount points in the form: host:dirpath
-d List directory paths of mount points instead of hosts.
-e Show the host's exports list.
-3 Use mount protocol Version 3, compatible with NFS Version 3.
-6 Use only IPv6 addresses to contact servers.
SEE ALSO
mount(1), mountd(8), nfsd(8), mDNSResponder(8)
BUGS
The mount daemon running on the server only has an idea of the actual mounts, since the NFS server is stateless. showmount will only display
the information as accurately as the mount daemon reports it.
HISTORY
The showmount utility first appeared in 4.4BSD.
4th Berkeley Distribution September 26, 2010 4th Berkeley Distribution