07-24-2007
Also confirm you are using the default ethernet packet type for IPv4 (not using SNAP).
10 More Discussions You Might Find Interesting
1. Programming
Hi,
I am using gmake to compile a c program with a makefile. The make file runs ld. I get the following error
jsh1035c:/users/egate453/admegate/kapil/samples $ gmake -e -f GNUmakefile queue_c
gmake -f ./GNUmakefile queue_c in_objdir=1 build_root=/users/egate453/admegate/kapil/samples... (2 Replies)
Discussion started by: handak9
2 Replies
2. Shell Programming and Scripting
Somewhat long story:
I have a simple Perl CGI script that uses Expect to Telnet to a device and grab some data, and then spits it back to Perl for display on the Webpage.
This works for many devices I've tried, but one device just fails, it keeps rejecting the password on this device, only... (1 Reply)
Discussion started by: jondo
1 Replies
3. UNIX for Advanced & Expert Users
Usually when su rejects an attempt to switch user it responds with "Sorry" but with a certain username on some unix servers the response is "Killed". I'm guessing the su accepted the username/password but refused to spawn child shell with the specified username. What's causing this and what has to... (8 Replies)
Discussion started by: twk
8 Replies
4. Solaris
Hi,
I telnet to the localost in new install Sun 5.10
I get below error
I also telnet from other to this mahcine but get "access deny" after input root password.
The password is correct as I can login in console
"Not on system console
connection to unknown cloase by foregin host"
Why ,... (25 Replies)
Discussion started by: chuikingman
25 Replies
5. Shell Programming and Scripting
Hi
I wanna automate the telnet process for port connection..
# telnet 0 port_number
Trying 0.0.0.0...
Connected to 0.
Escape character is '^]'.
If its connected how to make it disconnect automatically..
And how to check for success or failure.. (0 Replies)
Discussion started by: ningy
0 Replies
6. Shell Programming and Scripting
Hi,
I am running a shell script which will spawn the telnet and login.
But sometimes, the telnet session itself is not getting spawned.
My requirement is, if the telnet session is not spawned, the user must be notified that it failed.
Is there any command to capture the status of telnet... (2 Replies)
Discussion started by: merin
2 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I was writing one script which includes to switch to the another telnet automatically from the present telnet server. I was using rlogin but firstly it takes the same user name of the present telnet and secondly it is prompting for the password.
But i want to switch to the another telnet... (2 Replies)
Discussion started by: Prateek
2 Replies
8. Red Hat
I am configuring Samba on one of my vmware.when i put smbclient -L local its showing error message : NT_STATUS_LOGON failure.I found that when i remove "Encrypted password entry from smb.conf" it works.
pls help me
---------- Post updated at 08:39 PM ---------- Previous update was at 07:11 PM... (0 Replies)
Discussion started by: Vaibhav.T
0 Replies
9. UNIX for Dummies Questions & Answers
hi power went out. next day unix sco wont boot up error code 303. any help appreciated as we are clueless. (11 Replies)
Discussion started by: fredthayer
11 Replies
10. UNIX for Dummies Questions & Answers
Hi,
I want to know the difference between these two services. Both are under xinetd. Both are used for enabling and disabling Telnet service. So, can somebody please explain me the difference between the two ?
Thanks in advance :) (0 Replies)
Discussion started by: kashifsd17
0 Replies
LEARN ABOUT DEBIAN
setether
SETETHER(8) System Manager's Manual SETETHER(8)
NAME
setether - Set the ethernet address for use with DECnet
SYNOPSIS
setether <if> [<if>...]|all [options]
DESCRIPTION
Set ethernet MAC address on ethernet adaptors
This script should be run at system startup. It will change the ethernet hardware (MAC) address of any or all ethernet interfaces to match
the DECnet node address. DECnet requires that the MAC address of all ethernet adaptors running the protocol be set approriately. If you do
not run setether then you must change the ethernet address in some other way for DECnet to work.
By default no ethernet interfaces will have their MAC addresses changed by setether, if you specify all then all interfaces name eth* will
be changed, otherwise a list of interface names can be specified. setether will enable (UP) all interfaces it changes the MAC addresses
of.
(2.4 only) The first interface specified on the command-line will also be made the default interface for DECnet operations (ie attempts to
contact nodes not in the neighbour table will be done over this interface).
This script must be run with the interface inactive, it is normally run from /etc/init.d/decnet before TCP/IP starts up.
EXAMPLES
set the MAC address of eth0.
# /sbin/setether eth0
set the MAC address of all ethernet interfaces
# /sbin/setether all
HELPFUL HINTS
If you have multiple ethernet cards on your system and they are connected to the the same network you should specify which one you want to
use for DECnet communication on the setether command line, otherwise they will both be given the same MAC address and this is probably not
what you want.
Running DECnet on multiple ethernet interfaces only works under Linux 2.4. If you are running Linux 2.2 then the interface name on the
setether command line must match the one in /etc/decnet.conf(5).
SEE ALSO
decnet.conf(5), dntype(1), dndir(1), dndel(1), dnetd(8), dnping(1)
DECnet utilities March 01 2001 SETETHER(8)