07-24-2007
Have you tried looking at the system log or the log for the network device/switch it is attatched to(in this case the blade center as well)? It sounds like your blade is dropping off the network.
Cheers,
Keith
10 More Discussions You Might Find Interesting
1. Programming
Hi,
I am using gmake to compile a c program with a makefile. The make file runs ld. I get the following error
jsh1035c:/users/egate453/admegate/kapil/samples $ gmake -e -f GNUmakefile queue_c
gmake -f ./GNUmakefile queue_c in_objdir=1 build_root=/users/egate453/admegate/kapil/samples... (2 Replies)
Discussion started by: handak9
2 Replies
2. Shell Programming and Scripting
Somewhat long story:
I have a simple Perl CGI script that uses Expect to Telnet to a device and grab some data, and then spits it back to Perl for display on the Webpage.
This works for many devices I've tried, but one device just fails, it keeps rejecting the password on this device, only... (1 Reply)
Discussion started by: jondo
1 Replies
3. UNIX for Advanced & Expert Users
Usually when su rejects an attempt to switch user it responds with "Sorry" but with a certain username on some unix servers the response is "Killed". I'm guessing the su accepted the username/password but refused to spawn child shell with the specified username. What's causing this and what has to... (8 Replies)
Discussion started by: twk
8 Replies
4. Solaris
Hi,
I telnet to the localost in new install Sun 5.10
I get below error
I also telnet from other to this mahcine but get "access deny" after input root password.
The password is correct as I can login in console
"Not on system console
connection to unknown cloase by foregin host"
Why ,... (25 Replies)
Discussion started by: chuikingman
25 Replies
5. Shell Programming and Scripting
Hi
I wanna automate the telnet process for port connection..
# telnet 0 port_number
Trying 0.0.0.0...
Connected to 0.
Escape character is '^]'.
If its connected how to make it disconnect automatically..
And how to check for success or failure.. (0 Replies)
Discussion started by: ningy
0 Replies
6. Shell Programming and Scripting
Hi,
I am running a shell script which will spawn the telnet and login.
But sometimes, the telnet session itself is not getting spawned.
My requirement is, if the telnet session is not spawned, the user must be notified that it failed.
Is there any command to capture the status of telnet... (2 Replies)
Discussion started by: merin
2 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I was writing one script which includes to switch to the another telnet automatically from the present telnet server. I was using rlogin but firstly it takes the same user name of the present telnet and secondly it is prompting for the password.
But i want to switch to the another telnet... (2 Replies)
Discussion started by: Prateek
2 Replies
8. Red Hat
I am configuring Samba on one of my vmware.when i put smbclient -L local its showing error message : NT_STATUS_LOGON failure.I found that when i remove "Encrypted password entry from smb.conf" it works.
pls help me
---------- Post updated at 08:39 PM ---------- Previous update was at 07:11 PM... (0 Replies)
Discussion started by: Vaibhav.T
0 Replies
9. UNIX for Dummies Questions & Answers
hi power went out. next day unix sco wont boot up error code 303. any help appreciated as we are clueless. (11 Replies)
Discussion started by: fredthayer
11 Replies
10. UNIX for Dummies Questions & Answers
Hi,
I want to know the difference between these two services. Both are under xinetd. Both are used for enabling and disabling Telnet service. So, can somebody please explain me the difference between the two ?
Thanks in advance :) (0 Replies)
Discussion started by: kashifsd17
0 Replies
LEARN ABOUT DEBIAN
pppoeconf
PPPOECONF(8) System Manager's Manual PPPOECONF(8)
NAME
pppoeconf -- configures a PPPoE (ADSL) connection
SYNOPSIS
pppoeconf [-nox] [iface]
DESCRIPTION
The pppoeconf program is user-friendly dialog based setup tool for pppd (and pppoe if needed). It will look for existing ethernet
cards and look for ADSL hardware connected to one of them. You can add an interface name iface to force pppoeconf to use it. Then it will
get some login info and do some minor modifications to make working settings. Note that you can use ESC key to exit program when you wan.
OPTIONS
-nox Force ncurses use.
FILES
/etc/ppp/peers/dsl-provider is pppd options file for your dsl provider.
/etc/ppp/pap-secrets and /etc/ppp/chap-secrets are described in pppd documentation. pppoeconf may add lines to theses files.
/etc/ppp/ip-up.d/0clampmss and /etc/ppp/ip-down.d/0clampmss are used to clamp MSS if needed.
/etc/network/interfaces is network interface file for your system.
SEE ALSO
pppd(8), interfaces(5), pon(1) and pppoe(8).
AUTHOR
This manual page was originally written by Eduard Bloch (blade@debian.org) and now maintained by Gregory Colpart (reg@evolix.fr) for the
Debian GNU/Linux system (but may be used by others). This document is free software; you can redistribute it and/or modify it under the
terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option)
any later version.
On Debian systems, the complete text of the GNU General Public License can be found in /usr/share/common-licenses/GPL.
PPPOECONF(8)