07-24-2007
telnet failure
My hardware is a JS21 IBM server with AIX 5.3L. I can console into the blade but at times I am able to telnet to a LDAP server on port 389, but then there are times I can not telnet to the port. I can't ping the server when I experience this issues. My application I support goes down in flames and the users complain. I am able at the same time to telnet to the server from a different blade. Could anyone please let me know where to look for errors or troubleshooting steps -Thx
10 More Discussions You Might Find Interesting
1. Programming
Hi,
I am using gmake to compile a c program with a makefile. The make file runs ld. I get the following error
jsh1035c:/users/egate453/admegate/kapil/samples $ gmake -e -f GNUmakefile queue_c
gmake -f ./GNUmakefile queue_c in_objdir=1 build_root=/users/egate453/admegate/kapil/samples... (2 Replies)
Discussion started by: handak9
2 Replies
2. Shell Programming and Scripting
Somewhat long story:
I have a simple Perl CGI script that uses Expect to Telnet to a device and grab some data, and then spits it back to Perl for display on the Webpage.
This works for many devices I've tried, but one device just fails, it keeps rejecting the password on this device, only... (1 Reply)
Discussion started by: jondo
1 Replies
3. UNIX for Advanced & Expert Users
Usually when su rejects an attempt to switch user it responds with "Sorry" but with a certain username on some unix servers the response is "Killed". I'm guessing the su accepted the username/password but refused to spawn child shell with the specified username. What's causing this and what has to... (8 Replies)
Discussion started by: twk
8 Replies
4. Solaris
Hi,
I telnet to the localost in new install Sun 5.10
I get below error
I also telnet from other to this mahcine but get "access deny" after input root password.
The password is correct as I can login in console
"Not on system console
connection to unknown cloase by foregin host"
Why ,... (25 Replies)
Discussion started by: chuikingman
25 Replies
5. Shell Programming and Scripting
Hi
I wanna automate the telnet process for port connection..
# telnet 0 port_number
Trying 0.0.0.0...
Connected to 0.
Escape character is '^]'.
If its connected how to make it disconnect automatically..
And how to check for success or failure.. (0 Replies)
Discussion started by: ningy
0 Replies
6. Shell Programming and Scripting
Hi,
I am running a shell script which will spawn the telnet and login.
But sometimes, the telnet session itself is not getting spawned.
My requirement is, if the telnet session is not spawned, the user must be notified that it failed.
Is there any command to capture the status of telnet... (2 Replies)
Discussion started by: merin
2 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I was writing one script which includes to switch to the another telnet automatically from the present telnet server. I was using rlogin but firstly it takes the same user name of the present telnet and secondly it is prompting for the password.
But i want to switch to the another telnet... (2 Replies)
Discussion started by: Prateek
2 Replies
8. Red Hat
I am configuring Samba on one of my vmware.when i put smbclient -L local its showing error message : NT_STATUS_LOGON failure.I found that when i remove "Encrypted password entry from smb.conf" it works.
pls help me
---------- Post updated at 08:39 PM ---------- Previous update was at 07:11 PM... (0 Replies)
Discussion started by: Vaibhav.T
0 Replies
9. UNIX for Dummies Questions & Answers
hi power went out. next day unix sco wont boot up error code 303. any help appreciated as we are clueless. (11 Replies)
Discussion started by: fredthayer
11 Replies
10. UNIX for Dummies Questions & Answers
Hi,
I want to know the difference between these two services. Both are under xinetd. Both are used for enabling and disabling Telnet service. So, can somebody please explain me the difference between the two ?
Thanks in advance :) (0 Replies)
Discussion started by: kashifsd17
0 Replies
LEARN ABOUT SUNOS
mconnect
mconnect(1) User Commands mconnect(1)
NAME
mconnect - connect to SMTP mail server socket
SYNOPSIS
mconnect [-p port] [-r] [hostname]
DESCRIPTION
The mconnect utility opens a connection to the mail server on a given host, so that it can be tested independently of all other mail soft-
ware. If no host is given, the connection is made to the local host. Servers expect to speak the Simple Mail Transfer Protocol (SMTP) on
this connection. Exit by typing the quit command. Typing EOF sends an end of file to the server. An interrupt closes the connection immedi-
ately and exits.
OPTIONS
The following options are supported:
-p port Specify the port number instead of the default SMTP port (number 25) as the next argument.
-r "Raw" mode: disable the default line buffering and input handling. This produces an effect similar to telnet(1) to port
number 25.
OPERANDS
The following operand is supported:
hostname The name of a given host.
USAGE
The mconnect command is IPv6-enabled. See ip6(7P).
FILES
/etc/mail/sendmail.hf help file for SMTP commands
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
telnet(1), sendmail(1M), attributes(5), ip6(7P)
Postel, Jonathan B., RFC 821, Simple Mail Transfer Protocol, Information Sciences Institute, University of Southern California, August
1982.
SunOS 5.10 9 Nov 1999 mconnect(1)