07-24-2007
telnet failure
My hardware is a JS21 IBM server with AIX 5.3L. I can console into the blade but at times I am able to telnet to a LDAP server on port 389, but then there are times I can not telnet to the port. I can't ping the server when I experience this issues. My application I support goes down in flames and the users complain. I am able at the same time to telnet to the server from a different blade. Could anyone please let me know where to look for errors or troubleshooting steps -Thx
10 More Discussions You Might Find Interesting
1. Programming
Hi,
I am using gmake to compile a c program with a makefile. The make file runs ld. I get the following error
jsh1035c:/users/egate453/admegate/kapil/samples $ gmake -e -f GNUmakefile queue_c
gmake -f ./GNUmakefile queue_c in_objdir=1 build_root=/users/egate453/admegate/kapil/samples... (2 Replies)
Discussion started by: handak9
2 Replies
2. Shell Programming and Scripting
Somewhat long story:
I have a simple Perl CGI script that uses Expect to Telnet to a device and grab some data, and then spits it back to Perl for display on the Webpage.
This works for many devices I've tried, but one device just fails, it keeps rejecting the password on this device, only... (1 Reply)
Discussion started by: jondo
1 Replies
3. UNIX for Advanced & Expert Users
Usually when su rejects an attempt to switch user it responds with "Sorry" but with a certain username on some unix servers the response is "Killed". I'm guessing the su accepted the username/password but refused to spawn child shell with the specified username. What's causing this and what has to... (8 Replies)
Discussion started by: twk
8 Replies
4. Solaris
Hi,
I telnet to the localost in new install Sun 5.10
I get below error
I also telnet from other to this mahcine but get "access deny" after input root password.
The password is correct as I can login in console
"Not on system console
connection to unknown cloase by foregin host"
Why ,... (25 Replies)
Discussion started by: chuikingman
25 Replies
5. Shell Programming and Scripting
Hi
I wanna automate the telnet process for port connection..
# telnet 0 port_number
Trying 0.0.0.0...
Connected to 0.
Escape character is '^]'.
If its connected how to make it disconnect automatically..
And how to check for success or failure.. (0 Replies)
Discussion started by: ningy
0 Replies
6. Shell Programming and Scripting
Hi,
I am running a shell script which will spawn the telnet and login.
But sometimes, the telnet session itself is not getting spawned.
My requirement is, if the telnet session is not spawned, the user must be notified that it failed.
Is there any command to capture the status of telnet... (2 Replies)
Discussion started by: merin
2 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I was writing one script which includes to switch to the another telnet automatically from the present telnet server. I was using rlogin but firstly it takes the same user name of the present telnet and secondly it is prompting for the password.
But i want to switch to the another telnet... (2 Replies)
Discussion started by: Prateek
2 Replies
8. Red Hat
I am configuring Samba on one of my vmware.when i put smbclient -L local its showing error message : NT_STATUS_LOGON failure.I found that when i remove "Encrypted password entry from smb.conf" it works.
pls help me
---------- Post updated at 08:39 PM ---------- Previous update was at 07:11 PM... (0 Replies)
Discussion started by: Vaibhav.T
0 Replies
9. UNIX for Dummies Questions & Answers
hi power went out. next day unix sco wont boot up error code 303. any help appreciated as we are clueless. (11 Replies)
Discussion started by: fredthayer
11 Replies
10. UNIX for Dummies Questions & Answers
Hi,
I want to know the difference between these two services. Both are under xinetd. Both are used for enabling and disabling Telnet service. So, can somebody please explain me the difference between the two ?
Thanks in advance :) (0 Replies)
Discussion started by: kashifsd17
0 Replies
LEARN ABOUT SUNOS
jms-ping
asadmin-jms-ping(1AS) User Commands asadmin-jms-ping(1AS)
NAME
jms-ping - checks to see if the JMS provider is up and running
SYNOPSIS
jms-ping --user admin_user [--password admin_password] [--host localhost] [--port 4848] [--passwordfile filename] [--secure|-s]
[--terse=false] [--echo=false] [--interactive=false]
Checks to see if the JMS provider is up and running. This command is supported in remote mode only.
OPTIONS
--user authorized domain application server administrative username.
--password password to administer the domain application server.
--host machine name where the domain application server is running.
--port port number of the domain application server listening for administration requests.
--passwordfile file containing the domain application server password.
--secure if true, uses SSL/TLS to communicate with the domain application server.
--terse indicates that any output data must be very concise, typically avoiding human-friendly sentences and favoring well-
formatted data for consumption by a script. Default is false.
--echo setting to true will echo the command line statement on the standard output. Default is false.
--interactive if set to true (default), only the required password options are prompted.
Example 1: Using jms-ping
asadmin> jms-ping --user admin --password adminadmin --host bluestar --port 4848 server1
JMS Ping Status=RUNNING
EXIT STATUS
0 command executed successfully
1 error in executing the command
asadmin-create-jmsdest(1AS), asadmin-delete-jmsdest(1AS), asadmin-list-jmsdest(1AS)
J2EE 1.4 SDK March 2004 asadmin-jms-ping(1AS)