Sponsored Content
Operating Systems Solaris Connecting Solaris to Airport network Post 302127239 by heru_90 on Tuesday 17th of July 2007 02:05:02 AM
Old 07-17-2007
what type your wireless, are you have installed and work properly, some type can't work with solaris (No have good drivers)...
 

7 More Discussions You Might Find Interesting

1. Solaris

Problems connecting Solaris 10 to network via ISP

I have just installed Solaris 10 (x86) on my PC, which is connected to an ISP via a Netgear DG834G firewall/modem router. I can't find the network. My router has the IP address 192.168.0.1 and my ISP assigned IP address is 214.159.X.Y I have edited various files based upon information I have... (7 Replies)
Discussion started by: christian_hicks
7 Replies

2. IP Networking

can i force connecting to local web server via internet network ?

Hello all this is general question , if i have web server installed in my local pc and i have client that connecting to that web server can i force it always to go via the internet network ? the reason im asking is .. that im noticed when i close my internet connection i still can connect to my... (2 Replies)
Discussion started by: umen
2 Replies

3. HP-UX

Connecting To An External Network Using A logical (PACKAGE) IP Address

Hie everyone, I am currently facing a problem whereby I can not connect to an external network from a package ip address on a HP-UX cluster. Below is the illustration: Primary Server IP Address : n.n.n.202 Secondary Server IP Address : n.n.n.212 Package IP Address : n.n.n.211 ... (1 Reply)
Discussion started by: cchilenga
1 Replies

4. IP Networking

Connecting to an SSN from an internal network

Hi I have an Apache Web server running on a Solaris 8 box that sits on a SSN. I have one desktop that connects to the SSN from the internal network and is recognised directly without using the gateway, all other desktops, laptops from inside the internal network connect to the SSN using the... (0 Replies)
Discussion started by: Bobby76
0 Replies

5. IP Networking

Connecting to DHCP network with Realtek interface

I have a Realtek 8139 interface in one of my machines and it will not connect to the network. /etc/rc.conf contains ifconfig_rl0="DHCP" and "rl0" was obtained from a dmesg. A network interface restart yields the following: # /etc/rc.d/netif restart Stopping network: lo0 rl0 fwe0 plip0. rl0: no... (3 Replies)
Discussion started by: figaro
3 Replies

6. Shell Programming and Scripting

connecting to network, auto-entering info

Hey guys, I just started college a few days ago. To my dismay, my school has a very frustrating wireless network access system. Every time you want to use the network, you need to open up a browser and get re-directed to a login page. Every access, you need to reenter the same username and... (1 Reply)
Discussion started by: Chain Breaker
1 Replies

7. Red Hat

Connecting using SSH in WAN network

i have been learning linux from some time for linux plus exam and learned SSH protocol and have practised to connect to remote computer within Lan network and able to sucesssfully connect it . using ssh username@hostname But i wish to ask how do i use same ssh protocol to connect to other ... (6 Replies)
Discussion started by: lobsang
6 Replies
BWI(4)							   BSD Kernel Interfaces Manual 						    BWI(4)

NAME
bwi -- Broadcom BCM43xx IEEE 802.11b/g wireless network driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device bwi device wlan device wlan_amrr device firmware Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_bwi_load="YES" DESCRIPTION
The bwi driver provides support for Broadcom BCM43xx based PCI/CardBus network adapters. It supports station and monitor mode operation. Only one virtual interface may be configured at any time. For more information on configur- ing this device, see ifconfig(8). This driver requires firmware to be loaded before it will work. The ports/net/bwi-firmware-kmod port needs to be installed before ifconfig(8) will work. HARDWARE
The bwi driver supports Broadcom BCM43xx based wireless devices, including: Card Chip Bus Standard Apple Airport Extreme BCM4306 PCI b/g Apple Airport Extreme BCM4318 PCI b/g ASUS WL-138g BCM4318 PCI b/g Buffalo WLI-CB-G54S BCM4318 CardBus b/g Buffalo WLI-PCI-G54S BCM4306 PCI b/g Compaq R4035 onboard BCM4306 PCI b/g Dell Wireless 1470 BCM4318 Mini PCI b/g Dell Truemobile 1400 BCM4309 Mini PCI b/g HP nx6125 BCM4319 PCI b/g Linksys WPC54G Ver 3 BCM4318 CardBus b/g Linksys WPC54GS Ver 2 BCM4318 CardBus b/g TRENDnet TEW-401PCplus BCM4306 CardBus b/g US Robotics 5411 BCM4318 CardBus b/g EXAMPLES
Join an existing BSS network (i.e., connect to an access point): ifconfig wlan create wlandev bwi0 inet 192.168.0.20 netmask 0xffffff00 Join a specific BSS network with network name ``my_net'': ifconfig wlan create wlandev bwi0 ssid my_net up Join a specific BSS network with 64-bit WEP encryption: ifconfig wlan create wlandev bwi0 ssid my_net wepmode on wepkey 0x1234567890 weptxkey 1 up SEE ALSO
arp(4), cardbus(4), intro(4), pci(4), wlan(4), wlan_amrr(4), ifconfig(8), wpa_supplicant(8) HISTORY
The bwi driver first appeared in FreeBSD 8.0. AUTHORS
The bwi driver was written for DragonFly BSD by Sepherosa Ziehau and subsequently ported to FreeBSD. BUGS
Some card based on the BCM4306 and BCM4309 chips do not work properly on channel 1, 2 and 3. BSD
May 16, 2009 BSD
All times are GMT -4. The time now is 10:52 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy