07-12-2007
Hi,
so far i now this is a hardware failure.
SCSI transport failed: reason 'reset': giving up
You can test the bevavior by changing the disk or/and the diskarray.
Best regards
joerg
8 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I just installed sun storedge 3310 connected to a sunfire 280R with a total siz of 680GB and now am trying to create filesystems.
issue format command and created my partitions, the largest size of the partition is 170GB. but I try to create new filesystems by using newfs like
newfs... (3 Replies)
Discussion started by: hassan2
3 Replies
2. Filesystems, Disks and Memory
Hello,
i have a a1000 connected to an e6500. There's a raid 10 (12 disks) on the a1000.
If i do a
dd if=/dev/zero of=/mnt/1 bs=1024k count=1000
and then look at iostat it tells me there's a kw/s of 25000.
But if i do a
dd of=/dev/zero if=/mnt/1 bs=1024k count=1000
then i see only a... (1 Reply)
Discussion started by: mbrenner
1 Replies
3. Solaris
Hi,
I want to know if there is a command available for obtaining the BIOS Serial Number on a Sun Fire V240 machine? Or is it a known issue that it cannot be obtained through any command?
Thanks,
Vineet (4 Replies)
Discussion started by: vineetd
4 Replies
4. Solaris
Hi,
we are having one sun v240 server, now this server is performing very slow,
checked using top, iostat and vmstat commands, output is looking normal, but the performance is very slow and generating more traffic in network,
how can we resolve this.
Regards
RJS (5 Replies)
Discussion started by: rajasekg
5 Replies
5. Solaris
hallo anybody know how to set alom mail alerty server with yahoomail ?
thank u?where i can find mail server address for yahoomail?thank (1 Reply)
Discussion started by: yanto85
1 Replies
6. Solaris
HI guys.
Bit of a noob so bear with me.
I have 2 new disks I want to add to my StorEdge 3310 but am getting lost in the steps. We have another 3310 (JBOD) that I was able to plug the disks into and they instantly showed up. Did a few minor commands after (drvconfig, devfsadm etc..) and I was... (4 Replies)
Discussion started by: jamie_collins
4 Replies
7. Solaris
I have a sun fire v240 server.
The output of prtdiag -v shows a failed fan.
There are 3 fans for cooling system board.
There is 1 fan for each of the powersupply (There are 2 powersupplies)
From the below output how do i know which fan is bad and whats its location... (3 Replies)
Discussion started by: Tirmazi
3 Replies
8. Solaris
Hi All, I'm new to this site. I have a few question since I'm in the process how to to repair my raid on Sun V240 Server.
1. How can we create RAID in Sun Sparc v240?
2. What utility can help people create RAID in Sun Sparc v240?
3. Do we need any special software to create the... (12 Replies)
Discussion started by: angkor
12 Replies
LEARN ABOUT OSX
tran_bus_reset
tran_bus_reset(9e) Driver Entry Points tran_bus_reset(9e)
NAME
tran_bus_reset - reset a SCSI bus
SYNOPSIS
#include <sys/scsi/scsi.h> int prefix
tran_bus_reset(dev_info_t *hba_dip, int level);
INTERFACE LEVEL
Solaris DDI
PARAMETERS
hba_dip The dev_info_t pointer associated with the SCSI HBA.
level The level of reset required.
DESCRIPTION
The tran_bus_reset() vector in the scsi_hba_tran(9S) structure should be initialized during the HBA driver's attach(9E). It is an HBA
entry point to be called when a user initiates a bus reset through device control interfaces.
tran_bus_reset() must reset the SCSI bus without resetting targets.
level will be one of the following:
RESET_BUS Reset the SCSI bus only, not the targets.
Implementation is hardware specific. If it is not possible to reset the SCSI bus without changing the state and operating mode of the tar-
gets, the HBA driver should not initialize this vector or return failure.
RETURN VALUES
tran_bus_reset() should return:
1 on success.
0 on failure.
ATTRIBUTES
See attributes(5) for a description of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
|Stability Level |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO
attributes(5), tran_quiesce(9E), scsi_hba_tran(9S)
SunOS 5.10 17 Mar 1999 tran_bus_reset(9e)