06-28-2007
Quote:
Originally Posted by
porter
That old chestnut! I couldn't install AIX 5.1 on my 43P until I updated the firmware on my CD-ROM drive, and I couldn't update the firmware until I installed AIX. I solved that by using yet another CD-ROM drive.
How did you get it to boot? I have a 43p which will not boot from the CDROM! Have you a boot floppy?
10 More Discussions You Might Find Interesting
1. AIX
I am trying to find PCI Ethernet cards that are compatible with the IBM RISC 6000 - B50 Power PC. None of the regular NIC's seem to have AIX drivers. Does anyone know of AIX drivers for standard PCI Ethernet NIC's or a non IBM NIC that works with the Model B50 at 10/100 MB ? (0 Replies)
Discussion started by: rahe
0 Replies
2. AIX
I am trying to locate a non IBM PCI Ethernet card that will work with the Model B50 RISC box. Alternatively, I need to find AIX drivers for standard PCI Ethernet NIC's ?. (0 Replies)
Discussion started by: rahe
0 Replies
3. Solaris
Hi all,
I have a SUN server Sun-Fire-V890 running solaris 9, with a remote system console .
Both the IP adresses of the server and the console are in a private network (address 10.67.xxx).
For some reasons I need to give the access to the server from outside address 194.xxx, but I prefer that... (2 Replies)
Discussion started by: aribault
2 Replies
4. AIX
Hi guys,
Got a tiny bit of a problem on one of our servers here at work. I installed AIX 5.3 on the server and that went fine. Then I upgraded to ML 5300-05-01, but now the system just hangs on boot.
The system starts up and the monitor comes on in few minutes, but a few seconds later when... (6 Replies)
Discussion started by: drchris
6 Replies
5. AIX
Greetings to all:
Gentlemen, I've tried extremely hard to hookup my notebook via the hyperterminal to my AIX box (IBM 7046-B50) by virtue of a cross-over cable. Don't know really whats going on ......to my surprise. The notebook says its hookedup successfully but shows no unix login prompt on... (6 Replies)
Discussion started by: mhatmi
6 Replies
6. AIX
To All:
I have this AIX machine (see boot process below). The problem was it hangs at:
The ctrmc Subsystem has been started. Subsystem PID is 11906..
I checked with other forums but their advise were just "strong punches in the air" with no specific explanation.
I really appreciate if... (6 Replies)
Discussion started by: aix_xia
6 Replies
7. Ubuntu
Boot process hangs after reaching the following line:
Adding 5853176k swap on /dev/mapper/mch-swap_1. Priority:-1 extents:1 across:5853176kUsing knoppix 6.2 as LiveCD, and mounting the partitions, I got the following:
# /etc/fstab: static file system information.
#
# Use 'blkid -o value -s... (0 Replies)
Discussion started by: fzaker
0 Replies
8. AIX
Hi all,
We have a old Power4 server with AIX version 5.3 installed. Upon boot up, it hangs right after the AIX welcome screen. On the diagnostic load progress LED indicator, I saw that it stopped at '0c32' then after awhile the LED would be blank. The screen on the monitor will hang at the black... (15 Replies)
Discussion started by: a_sim
15 Replies
9. Solaris
Hi Guys,
I have a SunBlade 1500 which I use to practice at home. Suddenly when I power on the server it just displays the solaris banner and Boot device: disk File and args: Then it stops and says " rebooting with command: boot"
It doesn't boot to the kernel. Is there anyway I can possibly... (5 Replies)
Discussion started by: cjashu
5 Replies
10. Solaris
Power server up runs through diagnostics.
Goes to the boot section and then the bit where the cursor is spinning and thats it. Hangs completely.
Any ideas? (10 Replies)
Discussion started by: psychocandy
10 Replies
itemap(1M) itemap(1M)
NAME
itemap - load an ITE (Internal Terminal Emulator) keyboard mapping.
SYNOPSIS
[options]
DESCRIPTION
The command loads a keyboard mapping into the ITE (the graphics console driver), or displays ITE keyboard mappings. is run by automati-
cally. It is not usually explicitly invoked by the user.
Options
Dump a keymap to standard output in hexadecimal notation.
Load the specified keymap into the kernel mapping table
used for keyboards.
Interactively prompt for a
keyboard mapping. scans the keymap database file for all mapping names beginning with a prefix. Each of these names is
displayed, and one must be selected.
The name of the keymap database file to be used for input.
The default is
Load the appropriate keymap.
scans the hardware for a keyboard, determines the language of that keyboard, and loads the keymap corresponding to that
keyboard.
Because cannot determine the language of keyboards, use the option when using with keyboards.
Load a specified keyboard map.
Once loaded, ITE uses the specified mapping.
When loading a keyboard mapping with the option, matches the suffix of the name of the specified keyboard mapping with
those found in to determine the keyboard language. This information is used by the ITE to perform ISO 7-to-8 bit conver-
sion. Keymap names added by users, via
should use the same suffixes as those already used in For example, a French keyboard mapping can be named for consistency
with existing and mappings. A mapping called would not match any suffix patterns found by itemap, and would result in
incorrect ISO 7-to-8 bit conversion.
Load the specified keymap into the kernel mapping table
used for keyboards.
Perform actions verbosely.
If a keymap for a
keyboard is loaded, write its name to file_name.
EXAMPLES
To automatically install the correct mapping for an keyboard:
To explicitly load the mapping for an keyboard:
To explicitly load the mapping for a keyboard:
To interactively choose a keyboard mapping:
To generate a list of the available keyboard mappings:
FILES
Keymap database editor
System keymap database
Contains mapping name configured for keyboards
SEE ALSO
ps2(7), termio(7), keymap_ed(1X111).
itemap(1M)