RS6K B50 Hangs at E140 on Boot Post: 302123966

10 More Discussions You Might Find Interesting

1. AIX

PCI Ethernet Cards for IBM RISC 6000 - B50's

I am trying to find PCI Ethernet cards that are compatible with the IBM RISC 6000 - B50 Power PC. None of the regular NIC's seem to have AIX drivers. Does anyone know of AIX drivers for standard PCI Ethernet NIC's or a non IBM NIC that works with the Model B50 at 10/100 MB ?

2. AIX

PCI Ethernet NIC's for IBM RISC 600 Model B50

I am trying to locate a non IBM PCI Ethernet card that will work with the Model B50 RISC box. Alternatively, I need to find AIX drivers for standard PCI Ethernet NIC's ?.

3. Solaris

Boot hangs up on solaris

Hi all, I have a SUN server Sun-Fire-V890 running solaris 9, with a remote system console . Both the IP adresses of the server and the console are in a private network (address 10.67.xxx). For some reasons I need to give the access to the server from outside address 194.xxx, but I prefer that...

4. AIX

AIX hangs on boot

Hi guys, Got a tiny bit of a problem on one of our servers here at work. I installed AIX 5.3 on the server and that went fine. Then I upgraded to ML 5300-05-01, but now the system just hangs on boot. The system starts up and the monitor comes on in few minutes, but a few seconds later when...

5. AIX

Trying to hookup my notebook to my IBM 7046-B50 type rack RS6000/AIX system

Greetings to all: Gentlemen, I've tried extremely hard to hookup my notebook via the hyperterminal to my AIX box (IBM 7046-B50) by virtue of a cross-over cable. Don't know really whats going on ......to my surprise. The notebook says its hookedup successfully but shows no unix login prompt on...

6. AIX

AIX hangs through the boot process

To All: I have this AIX machine (see boot process below). The problem was it hangs at: The ctrmc Subsystem has been started. Subsystem PID is 11906.. I checked with other forums but their advise were just "strong punches in the air" with no specific explanation. I really appreciate if...

7. Ubuntu

Boot hangs while adding swap

Boot process hangs after reaching the following line: Adding 5853176k swap on /dev/mapper/mch-swap_1. Priority:-1 extents:1 across:5853176kUsing knoppix 6.2 as LiveCD, and mounting the partitions, I got the following: # /etc/fstab: static file system information. # # Use 'blkid -o value -s...

8. AIX

AIX 5.3 Boot Hangs On Power4 Hardware

Hi all, We have a old Power4 server with AIX version 5.3 installed. Upon boot up, it hangs right after the AIX welcome screen. On the diagnostic load progress LED indicator, I saw that it stopped at '0c32' then after awhile the LED would be blank. The screen on the monitor will hang at the black...

9. Solaris

Server Hangs at boot

Hi Guys, I have a SunBlade 1500 which I use to practice at home. Suddenly when I power on the server it just displays the solaris banner and Boot device: disk File and args: Then it stops and says " rebooting with command: boot" It doesn't boot to the kernel. Is there anyway I can possibly...

10. Solaris

Solaris 10 - hangs during boot

Power server up runs through diagnostics. Goes to the boot section and then the bit where the cursor is spinning and thats it. Hangs completely. Any ideas?

LEARN ABOUT MINIX

grub

GRUB(8) 								FSF								   GRUB(8)

NAME

       grub - the grub shell

SYNOPSIS

       grub [OPTION]...

DESCRIPTION

       Enter the GRand Unified Bootloader command shell.

       --batch
	      turn on batch mode for non-interactive use

       --boot-drive=DRIVE
	      specify stage2 boot_drive [default=0x0]

       --config-file=FILE
	      specify stage2 config_file [default=/boot/grub/menu.lst]

       --device-map=FILE
	      use the device map file FILE

       --help display this message and exit

       --hold wait until a debugger will attach

       --install-partition=PAR
	      specify stage2 install_partition [default=0x20000]

       --no-config-file
	      do not use the config file

       --no-curses
	      do not use curses

       --no-floppy
	      do not probe any floppy drive

       --no-pager
	      do not use internal pager

       --preset-menu
	      use the preset menu

       --probe-second-floppy
	      probe the second floppy drive

       --read-only
	      do not write anything to devices

       --verbose
	      print verbose messages

       --version
	      print version information and exit

REPORTING BUGS

       Report bugs to <bug-grub@gnu.org>.

SEE ALSO

       update-grub(8), grub-install(8).

       The  full documentation for grub is maintained as a Texinfo manual in the grub-legacy-doc package.  If the info and grub programs are prop-
       erly installed at your site, the command

	      info grub

       should give you access to the complete manual.

grub (GNU GRUB 0.97)						   January 2013 							   GRUB(8)