06-27-2007
Quote:
Originally Posted by
craigp84
I've fixed this by downloading the latest version of firmware for my B50
That old chestnut! I couldn't install AIX 5.1 on my 43P until I updated the firmware on my CD-ROM drive, and I couldn't update the firmware until I installed AIX. I solved that by using yet another CD-ROM drive.
10 More Discussions You Might Find Interesting
1. AIX
I am trying to find PCI Ethernet cards that are compatible with the IBM RISC 6000 - B50 Power PC. None of the regular NIC's seem to have AIX drivers. Does anyone know of AIX drivers for standard PCI Ethernet NIC's or a non IBM NIC that works with the Model B50 at 10/100 MB ? (0 Replies)
Discussion started by: rahe
0 Replies
2. AIX
I am trying to locate a non IBM PCI Ethernet card that will work with the Model B50 RISC box. Alternatively, I need to find AIX drivers for standard PCI Ethernet NIC's ?. (0 Replies)
Discussion started by: rahe
0 Replies
3. Solaris
Hi all,
I have a SUN server Sun-Fire-V890 running solaris 9, with a remote system console .
Both the IP adresses of the server and the console are in a private network (address 10.67.xxx).
For some reasons I need to give the access to the server from outside address 194.xxx, but I prefer that... (2 Replies)
Discussion started by: aribault
2 Replies
4. AIX
Hi guys,
Got a tiny bit of a problem on one of our servers here at work. I installed AIX 5.3 on the server and that went fine. Then I upgraded to ML 5300-05-01, but now the system just hangs on boot.
The system starts up and the monitor comes on in few minutes, but a few seconds later when... (6 Replies)
Discussion started by: drchris
6 Replies
5. AIX
Greetings to all:
Gentlemen, I've tried extremely hard to hookup my notebook via the hyperterminal to my AIX box (IBM 7046-B50) by virtue of a cross-over cable. Don't know really whats going on ......to my surprise. The notebook says its hookedup successfully but shows no unix login prompt on... (6 Replies)
Discussion started by: mhatmi
6 Replies
6. AIX
To All:
I have this AIX machine (see boot process below). The problem was it hangs at:
The ctrmc Subsystem has been started. Subsystem PID is 11906..
I checked with other forums but their advise were just "strong punches in the air" with no specific explanation.
I really appreciate if... (6 Replies)
Discussion started by: aix_xia
6 Replies
7. Ubuntu
Boot process hangs after reaching the following line:
Adding 5853176k swap on /dev/mapper/mch-swap_1. Priority:-1 extents:1 across:5853176kUsing knoppix 6.2 as LiveCD, and mounting the partitions, I got the following:
# /etc/fstab: static file system information.
#
# Use 'blkid -o value -s... (0 Replies)
Discussion started by: fzaker
0 Replies
8. AIX
Hi all,
We have a old Power4 server with AIX version 5.3 installed. Upon boot up, it hangs right after the AIX welcome screen. On the diagnostic load progress LED indicator, I saw that it stopped at '0c32' then after awhile the LED would be blank. The screen on the monitor will hang at the black... (15 Replies)
Discussion started by: a_sim
15 Replies
9. Solaris
Hi Guys,
I have a SunBlade 1500 which I use to practice at home. Suddenly when I power on the server it just displays the solaris banner and Boot device: disk File and args: Then it stops and says " rebooting with command: boot"
It doesn't boot to the kernel. Is there anyway I can possibly... (5 Replies)
Discussion started by: cjashu
5 Replies
10. Solaris
Power server up runs through diagnostics.
Goes to the boot section and then the bit where the cursor is spinning and thats it. Hangs completely.
Any ideas? (10 Replies)
Discussion started by: psychocandy
10 Replies