I am trying to find PCI Ethernet cards that are compatible with the IBM RISC 6000 - B50 Power PC. None of the regular NIC's seem to have AIX drivers. Does anyone know of AIX drivers for standard PCI Ethernet NIC's or a non IBM NIC that works with the Model B50 at 10/100 MB ? (0 Replies)
I am trying to locate a non IBM PCI Ethernet card that will work with the Model B50 RISC box. Alternatively, I need to find AIX drivers for standard PCI Ethernet NIC's ?. (0 Replies)
Hi all,
I have a SUN server Sun-Fire-V890 running solaris 9, with a remote system console .
Both the IP adresses of the server and the console are in a private network (address 10.67.xxx).
For some reasons I need to give the access to the server from outside address 194.xxx, but I prefer that... (2 Replies)
Hi guys,
Got a tiny bit of a problem on one of our servers here at work. I installed AIX 5.3 on the server and that went fine. Then I upgraded to ML 5300-05-01, but now the system just hangs on boot.
The system starts up and the monitor comes on in few minutes, but a few seconds later when... (6 Replies)
Greetings to all:
Gentlemen, I've tried extremely hard to hookup my notebook via the hyperterminal to my AIX box (IBM 7046-B50) by virtue of a cross-over cable. Don't know really whats going on ......to my surprise. The notebook says its hookedup successfully but shows no unix login prompt on... (6 Replies)
To All:
I have this AIX machine (see boot process below). The problem was it hangs at:
The ctrmc Subsystem has been started. Subsystem PID is 11906..
I checked with other forums but their advise were just "strong punches in the air" with no specific explanation.
I really appreciate if... (6 Replies)
Boot process hangs after reaching the following line:
Adding 5853176k swap on /dev/mapper/mch-swap_1. Priority:-1 extents:1 across:5853176kUsing knoppix 6.2 as LiveCD, and mounting the partitions, I got the following:
# /etc/fstab: static file system information.
#
# Use 'blkid -o value -s... (0 Replies)
Hi all,
We have a old Power4 server with AIX version 5.3 installed. Upon boot up, it hangs right after the AIX welcome screen. On the diagnostic load progress LED indicator, I saw that it stopped at '0c32' then after awhile the LED would be blank. The screen on the monitor will hang at the black... (15 Replies)
Hi Guys,
I have a SunBlade 1500 which I use to practice at home. Suddenly when I power on the server it just displays the solaris banner and Boot device: disk File and args: Then it stops and says " rebooting with command: boot"
It doesn't boot to the kernel. Is there anyway I can possibly... (5 Replies)
Power server up runs through diagnostics.
Goes to the boot section and then the bit where the cursor is spinning and thats it. Hangs completely.
Any ideas? (10 Replies)
Discussion started by: psychocandy
10 Replies
LEARN ABOUT PHP
uptime
UPTIME(1) User Commands UPTIME(1)NAME
uptime - Tell how long the system has been running.
SYNOPSIS
uptime [options]
DESCRIPTION
uptime gives a one line display of the following information. The current time, how long the system has been running, how many users are
currently logged on, and the system load averages for the past 1, 5, and 15 minutes.
This is the same information contained in the header line displayed by w(1).
System load averages is the average number of processes that are either in a runnable or uninterruptable state. A process in a runnable
state is either using the CPU or waiting to use the CPU. A process in uninterruptable state is waiting for some I/O access, eg waiting for
disk. The averages are taken over the three time intervals. Load averages are not normalized for the number of CPUs in a system, so a
load average of 1 means a single CPU system is loaded all the time while on a 4 CPU system it means it was idle 75% of the time.
OPTIONS -p, --pretty
show uptime in pretty format
-h, --help
display this help text
-s, --since
system up since, in yyyy-mm-dd HH:MM:SS format
-V, --version
display version information and exit
FILES
/var/run/utmp
information about who is currently logged on
/proc process information
AUTHORS
uptime was written by Larry Greenfield <greenfie@gauss.rutgers.edu> and Michael K. Johnson <johnsonm@sunsite.unc.edu>
SEE ALSO ps(1), top(1), utmp(5), w(1)REPORTING BUGS
Please send bug reports to <procps@freelists.org>
procps-ng December 2012 UPTIME(1)