I am trying to find PCI Ethernet cards that are compatible with the IBM RISC 6000 - B50 Power PC. None of the regular NIC's seem to have AIX drivers. Does anyone know of AIX drivers for standard PCI Ethernet NIC's or a non IBM NIC that works with the Model B50 at 10/100 MB ? (0 Replies)
I am trying to locate a non IBM PCI Ethernet card that will work with the Model B50 RISC box. Alternatively, I need to find AIX drivers for standard PCI Ethernet NIC's ?. (0 Replies)
Hi all,
I have a SUN server Sun-Fire-V890 running solaris 9, with a remote system console .
Both the IP adresses of the server and the console are in a private network (address 10.67.xxx).
For some reasons I need to give the access to the server from outside address 194.xxx, but I prefer that... (2 Replies)
Hi guys,
Got a tiny bit of a problem on one of our servers here at work. I installed AIX 5.3 on the server and that went fine. Then I upgraded to ML 5300-05-01, but now the system just hangs on boot.
The system starts up and the monitor comes on in few minutes, but a few seconds later when... (6 Replies)
Greetings to all:
Gentlemen, I've tried extremely hard to hookup my notebook via the hyperterminal to my AIX box (IBM 7046-B50) by virtue of a cross-over cable. Don't know really whats going on ......to my surprise. The notebook says its hookedup successfully but shows no unix login prompt on... (6 Replies)
To All:
I have this AIX machine (see boot process below). The problem was it hangs at:
The ctrmc Subsystem has been started. Subsystem PID is 11906..
I checked with other forums but their advise were just "strong punches in the air" with no specific explanation.
I really appreciate if... (6 Replies)
Boot process hangs after reaching the following line:
Adding 5853176k swap on /dev/mapper/mch-swap_1. Priority:-1 extents:1 across:5853176kUsing knoppix 6.2 as LiveCD, and mounting the partitions, I got the following:
# /etc/fstab: static file system information.
#
# Use 'blkid -o value -s... (0 Replies)
Hi all,
We have a old Power4 server with AIX version 5.3 installed. Upon boot up, it hangs right after the AIX welcome screen. On the diagnostic load progress LED indicator, I saw that it stopped at '0c32' then after awhile the LED would be blank. The screen on the monitor will hang at the black... (15 Replies)
Hi Guys,
I have a SunBlade 1500 which I use to practice at home. Suddenly when I power on the server it just displays the solaris banner and Boot device: disk File and args: Then it stops and says " rebooting with command: boot"
It doesn't boot to the kernel. Is there anyway I can possibly... (5 Replies)
Power server up runs through diagnostics.
Goes to the boot section and then the bit where the cursor is spinning and thats it. Hangs completely.
Any ideas? (10 Replies)
Discussion started by: psychocandy
10 Replies
LEARN ABOUT DEBIAN
hxcopy
HXCOPY(1) HTML-XML-utils HXCOPY(1)NAME
hxcopy - copy an HTML file and update its relative links
SYNOPSIS
hxcopy [ -i old-URL ] [ -o new-URL ] [ file-or-URL [ file-or-URL ] ]
DESCRIPTION
The hxcopy command copies its first argument to its second argument, while updating relative links. The input is assumed to be HTML or
XHTML and may be slightly reformatted in the process.
If the second argument is omitted, hxcopy writes to standard output. In this case the option -o is required. If the first argument is also
omitted, hxcopy reads from standard input. In this case the option -i is required.
OPTIONS
The following options are supported:
-i old-URL
For the purposes of updating relative links, act as if old-URL is the location from which the input is copied. If this option is
omitted, the actual location of the first argument is used for calculating relative links.
-o new-URL
For the purposed of updating relative links, act as if new-URL is the location to which the input is copied. If this option is
omitted, the actual location of the second argument is used for calculating relative links.
ENVIRONMENT
To use a proxy to retrieve remote files, set the environment variables http_proxy and ftp_proxy. E.g., http_proxy="http://localhost:8080/"
BUGS
Unlike the last argument of cp(1), the last argument of hxcopy must be a file, not a directory.
The second argument must be a local file. Writing to a URL is not yet implemented. To work around this, replace hxcopy file.html
http://example.org/file.html by hxcopy -o http://example.org/file.html file.html tmp.html and then upload tmp.html to the given URL with
some other command, such as curl(1). The first argument, however, may be a URL. hxcopy will download the given file. (Currently only HTTP
is supported.)
EXAMPLE
Assume the HTML file foo.html contains a relative link to "../bar.html". Here are some examples of commands:
hxcopy foo.html bar/foo.html
The file foo.html is copied to ../bar/foo.html and the relative link to "../bar.html" becomes "../../bar.html".
hxcopy foo.html ../foo.html
The file foo.html is copied to ../foo.html and the relative link to "../bar.html" is rewritten as "bar.html".
hxcopy -i http://my.org/dir1/foo.html -o http://my.org/foo.html file1.html file2.html
The file file1.html is copied to file2.html and the relative link to "../bar.html" is rewritten as "bar.html". A command like this
may be useful to update files that are later uploaded to a server.
SEE ALSO cp(1), curl(1), hxwls(1)6.x 9 Dec 2008 HXCOPY(1)